Discuss What is the purpose of the multi9 contactors in the Electrical Forum area at ElectriciansForums.net

Welcome to ElectriciansForums.net - The American Electrical Advice Forum
Head straight to the main forums to chat by click here:   American Electrical Advice Forum

Reaction score
2
Hi, Last week I went to a property where the owners had just moved in. They wanted advice about various electrical things including a large DB filled with these multi9 TL contactors. Does anyone know what they are for and is it easy to remove them to change the board for a more conventional system?
 

Attachments

  • What is the purpose of the multi9 contactors multi9 - EletriciansForums.net
    multi9.jpg
    60.8 KB · Views: 80
Looks like the contactors are all controlling Radials, there is either local switched control for each of these or central control for all of them.
There may be a clue on the other DB section, more investigation required as to why it was done like this.

Check the link below



What is the purpose of the multi9 contactors multi9 contactors_LI (2) - EletriciansForums.net
 
Just a guess but maybe their incoming supply was insufficient for the load so rather than have the DNO upgrade the supply they had load shedding contactors installed.
 
Being separate for each room, I expect there is a thermostat in each room that controls each contactor.
 
It is unusual to see that sort of thing domestically but I guess there is/was a good reason for it being done. The trick is to find out why it was done!

If you can take a look at the control wires for the contactors hopefully you can find out which of the above suggestions are in place:
  • Load control for DNO limit (or maybe backup generator limit?)
  • Off-peak usage
  • Early "smart" control from thermostats back to central point
 
As pointed out by @snowhead, there's a reference on one of the MCBs to ElectraTech controls having been fitted, so there would once have been a central panel for managing the heating and high-load appliances. There's also an MCB and relay labelled 'SEB System' presumably feeding the output of the central tariff control receiver into the ElectraTech.

If there's no panel, it's probably all completely obsolete and the contactors can be bypassed. If you do rip it out and start afresh, and other components of the system e.g. the ElectraTech control box are still present, I might be interested to save them for the museum as an example of an early 'smart' energy management system.

I recently removed a more industrial-style version of the same with a bunch of contactors in a panel beneath the DB that were used for load shedding on a backup genny. I put the whole thing in back in the 80s in my early teens and never quite finished the control system, as cars and girls dragged me in other directions. But that was OK because there were hardly ever any power cuts, so no-one missed the missing bits. That is often the way with these load management contactor panels, just a bunch of contacts closed since forever. It did all suddenly kick in during the early 2000s and apparently seemed to work.
 
As already stated the only time I have seen single phases contacts used domestically like this is in all electric flats / houses to switch heating loads on/off via individual room stats
 
As pointed out by @snowhead, there's a reference on one of the MCBs to ElectraTech controls having been fitted, so there would once have been a central panel for managing the heating and high-load appliances. There's also an MCB and relay labelled 'SEB System' presumably feeding the output of the central tariff control receiver into the ElectraTech.

If there's no panel, it's probably all completely obsolete and the contactors can be bypassed. If you do rip it out and start afresh, and other components of the system e.g. the ElectraTech control box are still present, I might be interested to save them for the museum as an example of an early 'smart' energy management system.

I recently removed a more industrial-style version of the same with a bunch of contactors in a panel beneath the DB that were used for load shedding on a backup genny. I put the whole thing in back in the 80s in my early teens and never quite finished the control system, as cars and girls dragged me in other directions. But that was OK because there were hardly ever any power cuts, so no-one missed the missing bits. That is often the way with these load management contactor panels, just a bunch of contacts closed since forever. It did all suddenly kick in during the early 2000s and apparently seemed to work.
Electratech pioneered by Norweb installed hundreds back in the eighties.
 
Thanks for the replies. I have taken a few more photos. Does anyone know if it is straightforward to remove all of this and replace with a standard consumer unit?

Interestingly the house is all electric including storage rads, they have a 3 rate tariff and meter but the bill is less than £10 per month, faulty meter methinks.

The whole installation is protected by a 100mA RCD which trips when the rotary switch to the left of it is moved to 1 but I have no idea what that is for.
 

Attachments

  • What is the purpose of the multi9 contactors thumbnail_IMG_5513 - EletriciansForums.net
    thumbnail_IMG_5513.jpg
    119 KB · Views: 32
  • What is the purpose of the multi9 contactors thumbnail_IMG_5504 - EletriciansForums.net
    thumbnail_IMG_5504.jpg
    109.1 KB · Views: 32
  • What is the purpose of the multi9 contactors thumbnail_IMG_5499 - EletriciansForums.net
    thumbnail_IMG_5499.jpg
    65.9 KB · Views: 32
  • What is the purpose of the multi9 contactors thumbnail_IMG_5502 - EletriciansForums.net
    thumbnail_IMG_5502.jpg
    63.3 KB · Views: 31
  • What is the purpose of the multi9 contactors thumbnail_IMG_5498 - EletriciansForums.net
    thumbnail_IMG_5498.jpg
    65.4 KB · Views: 34
What's the reason for wanting to replace it?
It's quite likely that the customer is going to spend a lot of money and end up paying a far higher electricity bill unless you put some other form of control on all the heating which takes advantage of the 3 rate tariff.

If you check out the Electratech Professional manual I linked to earlier, it explains exactly what the Electratech system does.
 
We are just weighing up options at the moment but they would like the storage rads removed and something more controllable installed. So not definitely replacing it but just trying to find out more about it.
 

Reply to What is the purpose of the multi9 contactors in the Electrical Forum area at ElectriciansForums.net

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Electrical Forum

Welcome to the Electrical Forum at ElectriciansForums.net. The friendliest electrical forum online. General electrical questions and answers can be found in the electrical forum.
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock