SuperlecDirect - ElectriciansForums.net Electrical Suppliers
This official sponsor may provide discounts for members
Advertisement - Content continues below

accenta

Advertisement - Content continues below
  1. R

    Honeywell accenta gen4 alarm.

    My Alarm has went off randomly last couple of nights, when I enter into engineer mode to look through the menu options there is certain options that are missing. When I’m in engineer mode I get 0 = walk test 1= alarm test Then it’s goes to number 4= date and time And there is other ones...
  2. B

    Honeywell Accenta G4 Mini with LED Keypad

    Hi, could do with some help please. I installed a Accenta G4 Mini alarm system with x3 LED keypads about 4 years ago which has been working fine. About 2 months ago the garage keypad speaker stopped working however the keypad still worked fine for setting/unsettling. About 1 week ago another...
  3. Ben Keer

    Honeywell accenta g4

    I have an accenta G4 system which haven't used for a couple of years and the bell box only sounds for a few seconds once activated then turns off. It works on bell test and the internal keypad sounder works ok but I can't find anything in the setup which would suggest anything wrong. Bell delay...
  4. J

    Domestic Programming key switch on an accenta G4

    Hi can anyone one run through how I program a zone as a keyswitch on the accenta G4 alarm it has the remote key pad. I've installed a Konnected wireless interface which has a relay for setting the alarm from a mobile but I can't find the instructions for setting the zone as a keyswitch in the...
  5. 877

    Accenta alarms (explain keyswitch and set to an idiot)...

    So I have two alarm panels (garage and home): Accenta 6 - has keyswitch and set terminals Accenta Optima G3 - zones can be configured to keyswitch or 'push to set', Could someone explain them in plain english and how they would be used practially? Many thanks Info attached: Accenta 6 info...
  6. B

    Accenta 6 replacement RKP problem

    Just replaced one of 2 RKPs within Accenta 6 system with ADE Gen4 keypad without trouble. Both lights are on, all buttons produce a beep and the existing code both sets and unsets the system. Twin button SOS feature also works. However cannot get into the program functions using either the...
  7. N

    Honeywell Accenta G4 - Silent Alarm Set

    Hi All Just installed a Honeywell Accenta G4 and everything works perfectly. I have a remote keypad upstairs on the landing. I have Program 2 set to activate all downstairs zones, which we use at night. Program 2 is set to arm itself silently. I type in our alarm code and press P to silence...
  8. T

    Honeywell Accenta zone problem!!

    Just installed a Honeywell Accenta alarm and having some trouble with a zone. Basically, when the alarm is set and the front door contact is broke, the alarm gives me time to put the code in to deactivate. Unfortunately the PIR in the hallway is activated and triggers the alarm to go off fully...
  9. T

    Honeywell G4 Accenta Remote Keypad

    Hi all, just powered up a G4 Accenta and I'm having trouble with the remote keypad. The red and green indicator led's are lighting up,but thats it. Nothing on the lcd display,no backlighting and no response to putting default code (0123) in. This is a brand new system,straight out the box. I've...
  10. T

    Honeywell Accenta G4 Remote Keypad problem

    Hi all, just powered up a G4 Accenta and I'm having trouble with the remote keypad. The red and green indicator led's are lighting up,but thats it. Nothing on the lcd display,no backlighting and no response to putting default code (0123) in. This is a brand new system,straight out the box. I've...
  11. B

    Accenta Gen4 - Magnetic Contacts Repeat Failure.

    Something I have found nobody has experienced before, just me unfortunately, but I thought I'd try you guys for one last fault finding. Thank you in advance. Over some years I have had to keep replacing the magnetic contacts on my outbuilding where I have the Accenta Gen4 system setup. Issue...
  12. S

    Accenta Optima Compact PA Disconnecting

    I have just bought a house that has a Accenta Optima Compact installed. It is a previously rented house and has a Personal Attack Alarm in both bedrooms. If I put the panel into engineers mode and disconnect the PA terminals will this disconnect the Pas or will I need to put a jumper over the Pa...
  13. crooksy88

    Accenta G4 external siren only sounds on bell test

    Hi, I have an Accenta G4 8SP399A with a single LCD keypad. Everything seems to be working correctly other than the external bell doesn't sound when the alarm is triggered, the strobe lights do light up though. If I do a bell test via the engineers menu the external bell does sound. Would...
  14. Steveo

    Honeywell ADE Accenta G4 panel & 8EP417A RKP?

    Honeywell ADE Accenta G4 panel & 8EP417A RKP Wondered if anyone can help please. Just installed the above & initially had a problem with tamper lock out ! Suspected the exterior bell/strobe, so bridged A&T on panel.(will sort the tamper switch later) That cleared the fault. So carried on with...
  15. Steveo

    Honeywell ADE Accenta G4 panel & 8EP417A RKP?

    Been trying to put this in the Security alarm forum !! but no joy.
  16. Steveo

    Honeywell ADE Accenta G4 panel & 8EP417A RKP?

    Wondered if anyone can help please. Just installed the above & initially had a problem with tamper lock out ! Suspected the exterior bell/strobe, so bridged A&T on panel.(will sort the tamper switch later) That cleared the fault. So carried on with setting the rkp ! walk test seemed to work and...
  17. D

    Help please with my house alarm

    Firstly hello, I am new to this forum :waving:. I am looking for some advise on my newly purchased alarm kit. I know this isn't them alarm section of the forum but that part of the forum is private. I brought myself a HW8GSM kit. It comes with a accenta g4 panel, which the manual states that no...
  18. F

    Alarm wiring

    please help!!!! Im wiring a accenta 8 alarm panel but using a texecom siren/strobe outside, but Im stuck on wiring them together. Anyone got a clue coz im clueless, only some of the time that is!
  19. D

    alarm parts interchangable

    Can someone advise me if wired alarm parts are normally interchangeable with other makes? Customer has a accenta G6 panel but wants new keypad and PIR's as existing ones are looking a bit tatty. Never actually replaced alarm parts, only fitted complete systems so unsure if you can use different...
  20. W

    alarm telecommunicator

    hi, sorry i know this isnt in alarms, but it wont let me post in there, im after a telecommunicator for an accenta g4 alarm panel, cant seem to find one and im wondering if they have another name, any help guys?
  21. J

    Ademco Alarm - unknown codes replace with acceta G4

    Hi, I have just buying a house that has a Ademco alarm. The box is under the stairs (plastic square box with Ademco moulded in) below is a separate keypad, with keys on the right, and leds on the left (zone1, zone2 etc up to 8) I suspect that the alarm is not working (although the panel is...
Advertisement - Content continues below
Advertisement - Content continues below
Advertisement - Content continues below
Top Bottom