OK, cards on table - I don't know much about these devices but got a call to look at one today...
So 4 way switch by door, 4 x 3 rows of lights, rows 1 to 3 inclusive all "working OK"
4th row stays on and is not responding to on/off or dimmer function at door switch.
Suggestios...
Octopus
Thread
can't
channel
contactor
controller
flashing
get
light
lights
switch
Hi everyone. Would be great to get some advice here if possible.
My home has (had!) three Aico Ei141 model smoke alarms, wired.
I decided to switch one of them out for a Nest Protect smoke detector which I did today. I switched off the power to switch to the Nest Protect (which meant all three...
hollaa01
Thread
alarm
flashing
green
help
home
issues
light
power
smoke
smoke alarm
I have fitted a brand new two tube florescent fitting in my garage - all starts up with no problem however after 5 minutes one of the florescent bulbs flashes on and off repeatedly. There is a slight buzzing sound when I turn the lights on.
When I turn the lights off and on again all runs OK...
Hi, I have an installation using JCC6 Led none dimmable down lights,
about 150 fittings installed , on initial switch on about 10 started flashing on & off, after a period of time ( 3 to 60 minuets) some settled down & remained on but a few continued flashing , These were replaced & worked...
Hi, I've installed two dimmer 60w Led bulbs, one in the bedroom and the other one in the dining room.
The first one is controlled by a 400w 2 Gangs 2 Way Dimmer BT (this one British General 2-Gang 2-Way 400W Push Dimmer Switch White | Dimmer Switches 400W | NoLinkingToThis) which control both the...
Hi all
Hope your all well.
Has anybody had a flashing tamper red led on a honeywell optima. I thought when you had a tamper fault its stays on and doesnt let you arm or disarm it. This one arm/disarms while the tamper lights flashing away. Ive not checked the tamper yet but will go back to...
Hi guys, we're currently putting in place a plan to stock/promote/distribute this solution for slate flashing when fitting PV. It was brought to my attention by a well-respected client of ours and we feel it is pretty nifty - anyone else have any experience or thoughts?
SolarFlash
Thanks in...
Alright guys so the Story, Just finished a job today so got all my tools home & went to charge my Drill Batts ready to start another Job tomorrow but The Charger starts Flashing red on one of the Batteries after a few secs , theres no damage to it (not been dropped or anything) Just The Chargers...
Hi, I am currently having problems with a sick safety relay not resetting, I can make it set (Energise) by applying 24VDC to K1 and K2 inputs, however when I try to make it reset using the PNP output from a retro-reflective sensor the K1 and K2 indicators flash? Any ideas? thanks
Hi,
I have an external floodlight without a switch on the inside. a few months back it started to come on, then go off for like 3 seconds, then come back on again, then off, then on. i changed the unit and the new one was fine. then the same started to happen again with the new one. surely i...
Was called to a pub today, to look at some LED down lights (small single LED's) built into a shelving unit. They flash rapidly on start up then stop and stay on permanently and intermittently start flashing again before returning to permanent. Once i had located the Transformers for them, I...
Hi everyone,
can any one help with this little fault? i have been fitting new spot lights in a kitchen, In the process i found a earth fault, the earth disconnected in one part of the daisy change of the existing house wiring, so I fit the spots in the kitchen connect the earths back up only to...
Mitch
Thread
circuit
earth
fault
flashing
led
problem
spots
voltage
I have replaced 7 12v 50w halogen downlights, (removing transformers) and replaced with GU6WW downlights. The new GU10 base lamps have built in drivers so I don't believe I need extra resistance on the circuit. They were fine - but have now started flashing, all at once. An interesting one...
Hi all!
Just a question and hopefully not a huge problem. Ive just exchanged old downlights (R80's lamps) for new halogen GU10 downlights. The old wiring is still intact and pretty much everything else including the DB which is push button 5A breakers. I installed these last week and now i have...
Firstly I am am a DIY'er not an electrician.
Last night I noticed that the energy saving bulb in my landing light was flashing faintly even tough it was witched off..
It is two way switched, one switch on the landing and one in the hall, power feeds the switch on the landing, wiring is done...
dinsdale
Thread
across
bulb
bulbs
circuit
energy
flashing
saving
switch
switched
voltage
Hi..!
I had 2 soladin 600 gbr models 1 of them was and is still working which is the first grid tie inverter i bought. i used it since january- 2012 and then in start of june i got another soladin 600 and wired them together LL ,NN at the landis & gyr P.v. meter as its no different then...
bob2041
Thread
bought
fault
faulty
flashing
inverter
red
still
stuck
turned
working
Customer complaining of flashing lights - lights have been working for years but now something strange is happening.
Lights are low energy lamps and LED deck lights. Lights flash periodically.
Have initially investigated and have detected 12V on the circuit (disconnected from the supply). I...
Ghost busters????
This is great. I get to look like a right wally in front of customer over this one for a while! "Can you come and look at my lights? Something strange is happening." "Er? OK. See you soon". Alls well. I arrive and get given cup of tea. All nice and normal. "Come and look at...
Just a quickie, we've installed loads of Landis & Gyr 5235B generation meters but the last one I did alternately displayed an 'r' alongside a 0 kWh reading and then a 't' alongside the PV generated reading.
I guess it's a twin-rate display or some such thing; is that to be expected (and ignored)?
Folks,
Fitted a bank of 6 LED lights last week....3 x 4W lamps on 2 x 15W LED drivers. When I powered up they flash on and off. Taking them down to one LED lamp per driver they light normally.
I'm guessing that the flashing on/off is an under-power issue? Should a 15W driver be able to...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.