Hi,
I'm going to be installing an outdoor socket, have no problem with the outdoor/socket side, but when bringing the internal end or the SWA into the property, need to be able to switch it. Only have hollow plasterboard void to mount fused switched spur to. But unsure of how I should terminate...
Folks,
Is there any hard or fast rule on what should be on a plug/fused outlet. I am aware portable equipment - plug š. I recently did a PAT and everything is on plug. Likely everything max of 13A. This includes the shutter motors which are fixed outside (plug inside of course). I don't see or...
Hi folks,
Iām new to the forum and itās this issue that lead me here.
So first things first. I was looking to wire in a Smart Relay at the rose of my hallway light. Itās got two switches. Now I thought I had āokā knowledge when it came to wiring a socket / light switch / rose.
However...
I have a countdown timer switch hooked up to run my washroom fan. It stopped working all of a sudden.
I replaced it with a regular switch and the fan worked.
I took the old timer switch and hooked it up to another different washroom fan, and the old switch worked.
What am I missing?
Hi All, thanks in advance for any guidance you can provide. I will of course turn off everyhing at the consumer unit before doing anything.
I recently purchased a zigbee module for use with an on/off switch in my utility room that controls 5 GU10 spotlights. The zigbee module i purchased works...
When there exists a single-phase transfer switch within a 3-phase distribution system, is it necessary for both feeds to the transfer switch to be connected to the same phase on the two sources?
Take for example the image below, note that the transfer switches are connected to the power sources...
Hi,
I have recently bought a house and I have a fused switch in my living room which I don't know what it's for.
I believe it was a switch for a electric fireplace that has been removed but the switch was left there.
How can I check and could I possibly change it to a single plug socket...
Howdy DIY soldiers, first post here.
My question comes down to whether it would be particularly unsafe for me to temporarily wire nut and tape a neutral wire connected to an active knob and tube circuit and leave it in a wall behind a plastic box.
I know that the "correct" answer per the NEC...
I threw away an old knackered light switch and now need to replace it. It had 4 terminals (L1, L2, L3, L4) and is fed by two blue and two red wires. It has a single rocker.
I assume this is a 1 gang 3 way switch? If not what is it? Where can I get one?
I usually always take a picture before disconnecting electrical wiring and this time I did not.
I am trying to wire a 3way switch that controls lights at the top and bottom of the stairs.
In my box I have 2 3wire sets coming in. One set all 3 wires are live, and the other 3 I believe run...
Wrong forum? U.S. here. If yes...my apology.
Naively, I thought the number of wires, and the the wire colors, would match. House was built in 1989 in California.
Thank you....
Hi All,
I am looking to install a Quinetic double gang in line receiver switch (QURS2W) in my hallway on the ground floor to control the lights in the hallway on the ground as well as the first floor.
On the first floor, I propose to pair up a 2 gang Quinetic switch.
The wiring is all old and...
Hi we have been asked to run a 3 phase supply into a boiler house to feed a DB fed from next to the existing meter. Would we need to install Tails to a switch fuse or could we just install a rotary isolator? Just tight for space near the Meter and switch fuses are big. Thanks
Hey all - Iām trying to change out a switch only with a combo switch/outlet. After doing the wiring everything seemed to be working but I then realized that the switch also turned off the outlet? Is that normal behavior or did I get my wiring crossed? The combo Iām trying to install has a the...
Hi.. Newby here.. I have a couple lights holders/bulbs on the end of a flex plugged into the mains 13Amp plug. I want to put an inline switch on the cable so I donāt have to unplug/plug all the time.. WHat kind of switch do I need & how to wire earth/live/neutral? Many thanks - Dino
Hi. I am trying to replace a heating timer with a smart switch. The current timer is the type with a dial on the front and 1 to 24 written on it where you pull out the little lugs to set what time the heating comes on and how long it runs for, APT is the make. The wires coming from the wall are...
Looking for a little advise as Iām not sure whatās happening
So Iām looking at moving a two way light switch probably about 100cm away from its current location as itās obstructed
So I bought PRYSMIAN 6243YH three core and bare earth wire When I wired the existing switch connections up to...
hello all, pardon my ignorance in not employing an electrician, however, im a diy'er whos changing the light switches in my house and came across this unusual wiring for my downstairs loo. its a single light which has a fan which can be isolated as necessary. I ordered all the new chrome light...
Good evening,
I wondered how the MCB between RCD and the Main switch is wired while watching this video. Photo attached.
I assume a busbar link is connected to the main switch and mcb. Do the line conductors and the busbar connected at the same terminal and then go to the RCDSs?
Link to the...
My customer has just moved in and wants to make sure the electrics in the garage are safe. I have only carried out a pre-works visit so far and noticed this old MEM switch.
I believe it to be the isolation switch for all the garage electrics. Will it have a fuse inside it? Also, is this likely...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.