Hi there
I cannot find the regs page that will help me so maybe someone can help.
At the moment the bathroom light switch also activates a FAN. The bathroom has a openable window but I believe still its best to have an isolator so I want to fit the isolator, not sure if I can just break the...
can anyone please help with the wiring of a combi boiler that is to be moved into loft space using old programmer and wireless room stat.
as not done much boiler work not sure how to wire this, i have wired combies in the past but straight forward such as L,N,E from spur to boiler and then a...
Hi,
my electrician has installed a triple pole isolator wiring outside my bathroom, currently there is one triple and earth and two twin and earths, all the wiring diagrams i can find suggest there should be two triples installed, one in and one out, i am interested to understand what his plan...
Mrgee
Thread
extractor
extractor fan
fan
help please
please
wiringwiringhelp
Good morning ,
I have been asked to fit a mimic up/down button outside a loading bay dock leveller so that the exterior door can be opened from the outside but the internal door must remain closed at the same time- an airlock situation.
Inside the airlock is a control panel that will operate...
I have an ltc amplifier with 2 pin foriegn plug. Says china made on appliance. I cut off 2 pin plug to attach 3 pin uk and im not sure where to put wires as one is blue and 2 black ones? Theres also a socket for 12v use on rear of appliance .
Any ideas?
Kind regards
Today I have wired up 2 new zone valves and a 2nd thermostat to my heating system.
The existing system is a gravity fed boiler with no valves. It has a separate programmer and thermostat.
There is a 3 core and earth running from the programmer/thermostat to the boiler. I have broken into this...
i was trying to install 2 switched fused conenection units on a ring circuit. at the start of the job i cut through a live wire which tripped the whole db. i connected the fcus ok. then put a socket plate on another one which had been wired ready. when i turned the board on the socket with the...
I just got a 30A/50A dual power plug to fit into my dryer outlet I also got a 15ft dryer cable 10/2 with a ground the colors are white and then dark grey with a bare copper for ground. I'm trying to connect this to my 220v lead furnace. The wires off of my furnace are blue, grey, and green with...
Hi Guys, some advice would really help me:
Bedroom ceiling light keeps blowing bulbs so I have taken it down to fit new, however,,
wiring has me a bit confused, Ignoring the earths I have a 3 core & a 2 core cable,
3 core cable
A/ Red--------------------Permanently live
B/...
captain pugwash
Thread
aus
ceiling
ceiling rose wiringhelp
rose
wiringwiringhelp
Hi newby here, wondering if anybody could help me out with a emergency lighting question?
Had a call from a client about an emergency lighting not switching correctly. Basically theres a problem on a 2 way lighting system not illuminating some non maintaind when the key switch is operated...
Need help from any sparks familiar with wago wiring, started testing today in a new build hospital, all wiring is wago systems with home run boxes etc... Never came across this system and currently doing my dead tests ( r1 + r2 ins res ) however it seems to be a very time consuming task, has...
Hi
Hopefully someone can help me
Am replacing all the light switches in my house and have done them all without problem except this final one which is confusing me
The switch is a double switch but only one seems to do anything (kitchen fluorescent light), the other does nothing
It has 4...
wingers
Thread
anything
aus
black
earth
help
home
light
light switch
other
replacing
switch
switches
wires
wiringwiringhelp
Dear All,
Our company has a single phase induction motor Baldor make model VL5023A. It's a 1HP, 1725RPM, 1Ph, 60 Hz, 115/230 VAC single phase motor. More info can be found here https://www.baldorvip.com/servlet/productInfoPacket/VL5023A.pdf The last page of the pdf has the wiring diagram. LOW &...
blacklight186
Thread
aus
help
induction
motor
needed
phase
single
single phase
wiringwiringhelp
Hi, Im trying to replace a ceiling lamp but am a little confused with the wiring. Any advice would be greatly appreciated.
I have attached a picture of the old lamp as it is currently connected (the lamp cable has been removed but was connected where the red circles are). The second picture...
ABB
Thread
aus
ceiling
help
lamp
lampholder
lighting
lights
wiringwiringhelp
Hi all, I am sorry to bother you all with what will seem a silly point for most of the qualified people but I am in need of urgent help without going back to my sparky as we have had a falling out.
Basicly we recently had my shop re-wired which included a new 3phase supply. I had alll my range...
Hello everyone
I was after some advice on how to wire up downlights.
I have 3 downlights that i want to fit with all 3 of them to turn on by one switch.
I have taken down the ceiling rose down from the ceiling in my bedroom and pulled the wires through to the loft and wired them into a 3...
Mustang
Thread
aus
downlights
help
lighting
lights
wiringwiringhelp
Hi All!! i just need some advice on plug wiring please, i have an hifi amp from the usa and it has a feature to swap it from 120 to 240 volts which is ok, but the plug is the american type just 2 wire one black and the other black/white, is it ok to just put an english plug on with the black to...
I bought a siren like this one in the video and don't know how should I wire it
(link removed)
I have a red , black, white and blue .... red and black are positive and ground and the others are Alarm Trigger + and - , I wired the red one and the white one (trigger + ) to the alarm white ...
hi, i have supply from drive lights and now i have installed 2 outdoor lights and want to connect both (drive and outdoor) lights to 2 gang way any help how to do so? so its like 2 set of lights from 2 gangway switch. one side is working connected to common and L1 where does live and neutral...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.