Anybody with these?
I have been for two years and recently called to change policy cover to include 3 phase. Woman on the other end didn't understand the difference so I explained and she held me on hold while she spoke to the underwriters. When she got back to me she said as long as you are...
Hi,
I understand from the wiring regs that if I am to run a cable through a ceiling/floor joist I have to adhere to certain rules to keep it safe -50mm/armour etc.
I currently have a plasterboard ceiling with some holes in it. My plasterer will put another layer of plaster board over this when...
During fault finding I came across a switch wire and a perm wire connected the wrong way would this still be known as reversed polarity ? As the connections are reversed?
Hi everyone, I need serious help here I know theres a post on this before bit everyones answers seem wrong. I need someone who seriously knows what there on about, here is the question
Propriety Fixings of the PVC Conduit
I need a solid answer for this as I have college tomorrow thanks
SparkyWoolford
Thread
answer
answers
city and guilds
guilds
question
wrong
Hi all
ok...i was asked to wire a motor for a fan today....3 phase motor...it had its mains lead attached pre wired.
when we finished wiring the supply and starter i was surprised to see it was spinning in the wrong direction.......well not that surprised ...the owner got it from ebay from a...
Just looking at the Elex Show at Sandown, and Napit have a rather strange offer; NAPIT - £100 off selected applications. Looks like they are offering to give £100 towards joining Elecsa/NICEIC. How nice of them :hurray:
Or have I got that wrong :rofl:
A question to the experienced electricians out there...
I'm a mature 2365 level 3 student with plenty of previous DIY experience and over the last few months, have been lucky enough to have been doing some casual (as-and-when-needed) work with an all round fully approved electrician. Been doing...
Just been told by the letting agent that the last lot of EICR's I've done have been rejected by the council, because it's not on the official NIC form. Been using PIRForm for the last 3 years, not a problem until now.
Hi I've been pulled today for installing an swa glancing into the top of a header trunking then taking it through the db, saying its against the regs saying a once a main sw is off the whole db has to be dead, I can't find a reference to it,
normally I would always gland it in the bottom of the...
Hello All
Last week had a small bathroom to install new down lights, 3 down lights, install shaver (box in wall already & switch box outside) connect RCD unit inline & install shower pump RCD.
Hatch in bathroom & no more than 2.5 meters square, down lights marked & could get into loft standing...
looking at zs readings for type b bs60898 circuit breakers in bs7671 "page58" and looking at page 121 in the guidance notes 3 and seeing different readings??
Hi all, would you be able to confirm the attached diagram will do the described scenarios?
Original diagram
https://www.dropbox.com/s/fp4td333alpe335/800px-MultiPIRandLampCircuit%20Original.gif?dl=0
Amended
https://www.dropbox.com/s/vkbpfwp7atlc9vs/800px-MultiPIRandLampCircuit.gif?dl=0
I'm...
deridere
Thread
anything
diagram
lighting
pir
wiring
wiring diagram
wrong
Hi everone,I am new to the forum and think its brilliant,I am currently
studying for my 2394&2395 and am testing everything in sight with a
fluke 1651 multi functional tester.When i try to do a loop test on a lighting
circuit,I follow all the instuctions,but i keep getting >2000 ohms,i am...
Hi guys. I've recently moved from NAPIT to NICEIC I've just issued a cert. Now the circuit details are as follows.
Lighting, 6amp RCBO
Ze - 0.18
R1&R2 - 0.64
ZS - 0.82
Now by my understanding the max allowed ZS is 6.14 for the type of RCBO so I'm well within the allowed but on the generated...
Hello there, just had a triple light switch fitted but the order of the switches is wrong. The left and centre switches need to be swapped. Can someone please tell me how do I do this?
Picture:
Just been reading about Doody Toody helping Paul M and going to the wrong address, it reminded me of an incident which happened to me when I was working for SWEB in Bath.
We were give jobs via a card, go to stores pick up bits and proceed to job etc etc. Well the job was in John Colliers the...
I've got a shed load of dado trunking to purchase and install on a office refurb that im starting after christmas. Just wondering what people's opinions are on best make for ease of installation, cost etc. I normally use MK but its pricey but I like the way it all goes together, I've also used...
Hi Guys,
Recently got taken down the wrong path on Schneiders product selection on their website, ordered an MCCB 100a TP, easy, or so i thought, fitted new switch and on testing the swith find that i am missing a phase, MCCB has a CT module on the bottom of it which is proved to have voltage...
Hi guys....
Anyone come across this. We did an install for a customer. Original EPC was Band E. However after installing the system it got to Band D.
However the customer sent in the original EPC at Band E. When he sent in the new EPC EON have said its too late and they cannot amend his...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.