Discuss A2 and A3 radial circuits in the UK Electrical Forum area at ElectriciansForums.net

B

bf03yvd

Where some information regarding the above circuits, a more detailed version. My manual only gives a brief outline.:sorcerer:
 
A2 and A3 radial circuits are standard circuits classified in appendix H of the OSG.
The limitations that are relevant to these circuits without calculations can be determined from the information in chapter 7 of the OSG choosing the cable size and protective device parameters detailed in appendix H.
The A2 and A3 circuits are shown diagrammatically in appendix 15 of BS7671.
 
Where some information regarding the above circuits, a more detailed version. My manual only gives a brief outline.:sorcerer:

What manual are you referring to? opps someone has already asked that question
 
Last edited:
I think every trainee gets one. It came with a brief case and all the other resources. I'm not moaning though, just thought it should have come with an idiots guide too lol.
 
I think every trainee gets one. It came with a brief case and all the other resources. I'm not moaning though, just thought it should have come with an idiots guide too lol.

The only book i was told to purchase when attending college for day release each week was BS7671.

Can't say i have ever heard of Domestic installer version 4.0. This is issued from a short course provider i guess?
 
The domestic installer book version 4.0 which basically you need a PhD to understand it.[/QUOTE]

Now that i doubt very much!!

In years gone by you needed a pretty good math level to be taken on as an apprentice. Now the tecnical aspect of an electricians training hasn't changed much over the years, but the level of math of those that are now trying to get into the industry via the back door has.
 
The only book i was told to purchase when attending college for day release each week was BS7671.

Can't say i have ever heard of Domestic installer version 4.0. This is issued from a short course provider i guess?
Yeah i haven't been provided this Domestic installer Version 4.0... Am I missing out? will i fail my course without it? D: i've been told to buy an On-site guide
 
The domestic installer book version 4.0 which basically you need a PhD to understand it.[/QUOTE]

Now that i doubt very much!!

In years gone by you needed a pretty good math level to be taken on as an apprentice. Now the tecnical aspect of an electricians training hasn't changed much over the years, but the level of math of those that are now trying to get into the industry via the back door has.

To be accepted for an electrical apprenticeship nowadays you need to have GCSE's Maths & English or take an on line test to see what level they are at. They need to achieve at least level 1 to be accepted. Then at college, they will do functional skills level 2 in both, as well as their NVQ knowledge stuff, it's part of their framework.

But I don't know what, if any, Maths skills they need for the back door entry route!lol

Jay
 
To be accepted for an electrical apprenticeship nowadays you need to have GCSE's Maths & English or take an on line test to see what level they are at. They need to achieve at least level 1 to be accepted. Then at college, they will do functional skills level 2 in both, as well as their NVQ knowledge stuff, it's part of their framework.

But I don't know what, if any, Maths skills they need for the back door entry route!lol

Jay

There are one or two that need basic English skill though imo
 

Reply to A2 and A3 radial circuits in the UK Electrical Forum area at ElectriciansForums.net

Similar Threads

I have pulled out an old evaporative system I purchased many years ago from storage to have a look at it and see if I can get it running. Was...
Replies
1
Views
185
Hi guys I have some industrial lighting circuits to wire in a workshop and was after some fresh ideas/suggestions as to how i could best do this...
Replies
12
Views
1K
I had an interesting little job this morning. Three sockets in an extension were not working and haven't worked for quite some time (years). It...
Replies
0
Views
242
Came into work today with a fairly urgent requirement to install an instant hot water handwash unit in a small commercial kitchenette/servery -...
Replies
19
Views
2K
Browsing the OSG, I notice in section 7 that the data for ring finals assumes the load is distributed throughout the circuit, whereas the data for...
Replies
12
Views
2K

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Electrical Forum

Welcome to the Electrical Forum at ElectriciansForums.net. The friendliest electrical forum online. General electrical questions and answers can be found in the electrical forum.
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock