Discuss DIY Help - Joining 2 halves of a cut power cord in the DIY Electrical Advice area at ElectriciansForums.net

Welcome to ElectriciansForums.net - The American Electrical Advice Forum
Head straight to the main forums to chat by click here:   American Electrical Advice Forum

HL82

-
Reaction score
0
Hello -

I bought a corded hedge trimmer today and started using it. In about 5 minutes I had managed to chop through the cable! Rookie error. Here are the cut cable ends (I am in the UK btw)

DIY Help - Joining 2 halves of a cut power cord {filename} | ElectriciansForums.net
So I need to repair the cable. Having googled around, I could solder the wires together, but I don't much fancy my soldering skills - so I was thinking that it would be a lot easier instead if I could buy a 1 gang extension cable, remove both the plug and the socket end and then wire the plug to one end of my cut cable, and the socket to the other end and just plug them together.

Any reason this won't work or any reason I shouldn't do this? What is the best way to do this?

Cheers.
 
Hi,I would repair that,with a new lead.
I do not know how many times,you have used a powered hedge cutter,but your first ever cord repair,does not need to be this one:)
 
The connector types shown in the previous posts are not really suitable, as they easily pull apart.
You need a Flymo type connector:
B&Q 10A 2 Pin plug & socket | DIY at B&Q - https://www.diy.com/departments/b-q-10a-2-pin-plug-socket/171009_BQ.prd?utm_source=google_cpc&utm_medium=shopping&utm_campaign=PX_GSC_EPHC_+_Generic&ppc_type=shopping&ds_kids=92700041283649913&gclid=EAIaIQobChMIwr-zn4HY4AIVbRHTCh15nQzREAQYAyABEgI2F_D_BwE&gclsrc=aw.ds
Also the connector, should not be in a position in the lead where it will be dragging on the ground through wet grass.
You need to shorten the lead at the trimmer end to about 12 - 18 inches.
I would also suggest you consider purchasing an RCD plug:
RCD Plug - https://www.toolstation.com/rcd-plug/p99372
Having an RCD in your consumer unit is all well and good, as long as you test it regularly.
Having an RCD plug gives you the opportunity to test the RCD every time you use the trimmer.
 
Last edited by a moderator:
People keep suggesting having an RCD in circuit.
I think there is one already- owing to the fact that the OP is still here and not jiggling around on his back with a hedge trimmer in one hand and a severed flex in the other.
 
People keep suggesting having an RCD in circuit.
I think there is one already- owing to the fact that the OP is still here and not jiggling around on his back with a hedge trimmer in one hand and a severed flex in the other.

Dunno. Seen a few cut flexes where the 3036 wire stayed intact and the human operative suffered no ill effect. One of them even picked up the flex to inspect the damage :eek: (dopey friend of the missus)
 
My sister in law had a shock once from a grazed lawnmower cable. Hadn’t cut right through, but copper showing.
She had finished and was looping the flex round her hand to collect it up.

I told her to buy one of those RCD plug adaptors.
 
The connector types shown in the previous posts are not really suitable, as they easily pull apart.
You need a Flymo type connector:
B&Q 10A 2 Pin plug & socket | DIY at B&Q - https://www.diy.com/departments/b-q-10a-2-pin-plug-socket/171009_BQ.prd?utm_source=google_cpc&utm_medium=shopping&utm_campaign=PX_GSC_EPHC_+_Generic&ppc_type=shopping&ds_kids=92700041283649913&gclid=EAIaIQobChMIwr-zn4HY4AIVbRHTCh15nQzREAQYAyABEgI2F_D_BwE&gclsrc=aw.ds
Also the connector, should not be in a position in the lead where it will be dragging on the ground through wet grass.
You need to shorten the lead at the trimmer end to about 12 - 18 inches.
I would also suggest you consider purchasing an RCD plug:
RCD Plug - https://www.toolstation.com/rcd-plug/p99372
Having an RCD in your consumer unit is all well and good, as long as you test it regularly.
Having an RCD plug gives you the opportunity to test the RCD every time you use the trimmer.

Completely unnecessary if there is a RCD in the CU already. It just means you have 2 to reset when there is a fault.

Also quite often testing the RCD in the plug will trip the main RCD as well.
 
How close to one end is it damaged? If only a few meters might be best to just make the lead a few meters shorter and 'hard wire' it in.
Alternatively one of the many 'in line' connectors readily available (IP44 minimum).
 
Completely unnecessary if there is a RCD in the CU already. It just means you have 2 to reset when there is a fault.

Also quite often testing the RCD in the plug will trip the main RCD as well.
Yep, unnecessary, until you find the RCD in the CU has never been tested and is seized.
 
Hello - OP here again.

Noticed a few questions mentioning an RCD. Yep I have one fitted and I also have another cut-off in the extension reel I use, so hopefully I am safe there.

Update - I bought one of these - https://www.screwflix..com/p/masterplug-orange-connector-2-pin/46232 - after receiving a couple of recommendations to do so (thanks again). I fitted it tonight, but I have a question. Since the two halves of this plug can be slotted together either way round - is there not a risk that I would connect live to neutral? What would happen if I connected them the wrong way round?

I marked the outside of the plug so I know which way is the right way - but still, I'm curious to know if this is potentially dangerous.
 

Reply to DIY Help - Joining 2 halves of a cut power cord in the DIY Electrical Advice area at ElectriciansForums.net

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock