Discuss Which LED driver and how many? in the Electrical Forum area at ElectriciansForums.net

Welcome to ElectriciansForums.net - The American Electrical Advice Forum
Head straight to the main forums to chat by click here:   American Electrical Advice Forum

HappyHippyDad

-
Esteemed
Arms
Reaction score
5,578
I have a customer who wishes to have LED tape under the wall cabinets. I always fit 230V strip lights rather than tape as there is less to go wrong as no LED drivers involved. he would actually be ok with strip lights but has specified 2700K and I can only find tape in this rather than 230V strip lights. Anyone know where I can get some and therefore avoid the following...

I have not fitted tape before. I will be using a constant voltage LED driver as the lights will be in parallel. In total there will be perhaps 100w of tape. The diagram shows only 3 tapes, but in reality it will will cut into 6 or 7 bits from one strip.

My question is, is either of the following acceptable and which is best?
Is this just the same as if you were fitting MR16's downlights where each would usually have there own transformer? I would have thought it better to fit individual LED drivers as you will have a long run of cable which the 24V driver will have to deal with and VD may come into play, whereas with individual drivers they will be much closer to the light. Plus if the 100w driver fails all lights fail instead of just one. But, is this ok with each section of cut strip or do they have to have the same power supply?

Which LED driver and how many? driver - EletriciansForums.net
 
Either way will work OK.
Large wattage drivers tend to be very costly or open frame, which then need a ventilated enclosure, so I would tend to go for multiple fully enclosed drivers. The volt drop is only a problem if you join strip end to end; in your diagram you only have shorter runs of strip fed directly from the driver, wiring that way each strip only sees the volt drop for that strip.
You would only need to have the same power supply if the power supply were also a controller for colour changing, etc.
Work out where your driver will be and where you can run the cables and place junction boxes and make the strip to wire connections.
 
Either way will work OK.
Large wattage drivers tend to be very costly or open frame, which then need a ventilated enclosure, so I would tend to go for multiple fully enclosed drivers. The volt drop is only a problem if you join strip end to end; in your diagram you only have shorter runs of strip fed directly from the driver, wiring that way each strip only sees the volt drop for that strip.
You would only need to have the same power supply if the power supply were also a controller for colour changing, etc.
Work out where your driver will be and where you can run the cables and place junction boxes and make the strip to wire connections.
Thanks for the detailed reply Richard:)
 
I have a customer who wishes to have LED tape under the wall cabinets. I always fit 230V strip lights rather than tape as there is less to go wrong as no LED drivers involved. he would actually be ok with strip lights but has specified 2700K and I can only find tape in this rather than 230V strip lights. Anyone know where I can get some and therefore avoid ...
Hi - I'm guessing Customer wont accept 3000K ? They're quite close and easy to get, so perhaps worth an on site suitability check. :)
LED Linkable Striplights - https://www.tlc-direct.co.uk/Main_Index/Lighting_Menu_Index/Kitchen_Lighting/Ultra_Slim_KBU/index.html#Ultra_Slim_KBU_WW
 
Last edited:
Ive used Ledridge stuff before theyre not cheap but will do each section pre cut with fly leads and spec you what you need
 

Reply to Which LED driver and how many? in the Electrical Forum area at ElectriciansForums.net

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Electrical Forum

Welcome to the Electrical Forum at ElectriciansForums.net. The friendliest electrical forum online. General electrical questions and answers can be found in the electrical forum.
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock