Search results

  1. Dave OCD

    What is it on this fault

    More than once I've had customers ring to say the RCD lever is 'floppy' and won't latch on - always an MK one where you have to push the lever down first then up and they don't get it. :)
  2. Dave OCD

    Dodgy trade pictures for your amusement! - 1 Million Views!

    That metering arrangement would be very nice to have. :)
  3. Dave OCD

    Dodgy trade pictures for your amusement! - 1 Million Views!

    A flex outlet plate and shallow 16mm wall box, very poor. Are you sure there isn't a fused spur upstream of that Buzz ?
  4. Dave OCD

    Metal Tool Box or Alternatives

    I would hate to be the local shop keeper supplying this kind of stuff.......
  5. Dave OCD

    Points out of 10 for neatness?

    You lot are so over critical , I haven't quite finished that job yet, just a lick of Hammerite on the Wylex boxes and it'll be pristine. :)
  6. Dave OCD

    Can I simply change this over.

    Assuming there is also 30ma RCD protection in place for this circuit and the cable run is exactly as described I'd upgrade the MCB to a 50a if 45a isn't available. it's a bad idea for any overcurrent device to run at a slight overload constantly and although it probably wouldn't 'trip' an...
  7. Dave OCD

    40A shower disconnection time

    The thing that really gets on my nerves is counting all the 'points' per circuit - tedious ! In terms of a circuit that requires basic or additional protection [depending on the earthing arrangement] by a 30ma RCD then arguably it should disconnect within 300ms ?
  8. Dave OCD

    This could have been nasty...

    Exactly that , bloody scary eh ! :)
  9. Dave OCD

    This could have been nasty...

    We've been upgrading some bits and pieces in a rented house which hasn't had anything done for at least 40 years by the looks of it. The picture is where an old fused spur and box was being renewed as it was really manky and cracked too. This would once have been the external wall but a 'lean...
  10. IMG_5233 (1).jpg

    IMG_5233 (1).jpg

    • Dave OCD
    • Media item
    • Comments: 0
    • Category: Electrical Videos
  11. Dave OCD

    Dodgy trade pictures for your amusement! - 1 Million Views!

    What do you mean ? I finished it a while ago ! :)
  12. Dave OCD

    Planning garage sub-main project

    Yes that's right. Have a look at earthing or 'Piranha' nuts though, easier and IMO better than the old Banjo method. I'd be using 3 core SWA though.
  13. Dave OCD

    Planning garage sub-main project

    The right hand side of your board with the lighting MCBs isn't RCD protected and the blank will be a spare way- so subject to a decent Ze you could simply fit an additional matching MCB for the new SWA, but it will have to be glanded properly, possibly into a small metal enclosure to ensure the...
  14. Dave OCD

    Dodgy trade pictures for your amusement! - 1 Million Views!

    Very similar if not identical to Wylex MCBs of that era.
  15. Dave OCD

    Head scratching heating.

    Nice little bit of Pyro work in there, I realise that's no help at all though. :)
  16. Dave OCD

    Lucien Nunes Electrical Engineer Extraordinaire

    I've only just seen this and read every post, every single one is from the heart and confirm what an incredible man Lucien was. Personally I feel very sad , much more than you'd expect from someone you've never met, I think that says a lot about his influence on all of us too. I'd like to think...
  17. Dave OCD

    Dodgy trade pictures for your amusement! - 1 Million Views!

    With a TNCS the supplier never connects a main earth conductor, that's down to us - they provide the terminal only. I'd be tempted to arrange a quick visit from the seal fairy and have a little peek inside to see if there's a N-E link or one piece N & E block. I'd bet there is. :)
  18. Dave OCD

    Dodgy trade pictures for your amusement! - 1 Million Views!

    No they apply the stickers individually when fitting cutouts and will fit the appropriate one, have you done a Ze to the terminal under the blanking grommet ?
  19. Dave OCD

    Dodgy trade pictures for your amusement! - 1 Million Views!

    Sorry if I'm missing something here, but you do know the supply is TNCS there ?
  20. Dave OCD

    Electric Meter Switch Isolator wiring orientation

    I was once told by an ex navy Electrician that if common and L1 were swapped over in a one way switch it would then operate upside down ?! :)

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Workwear Shropshire
Top Bottom
Back