Recent content by mangoelectrics

  1. mangoelectrics

    Thermal Overload for TELEMECANIQUE LC1 D18 10?

    Thanks! I have now managed to confirm that the part that I mentioned does fit. Thanks again though…
  2. mangoelectrics

    Thermal Overload for TELEMECANIQUE LC1 D18 10?

    Good Morning All... Does anybody know what motor thermal overload would fit a TELEMECANIQUE LC1 D18 10? I need a 23A overload. Would this work TELEMECANIQUE LR2D2353? I can't seem to find any with the correct distance between the inlet 3phase connections for my contactor (photo attached). Thanks!
  3. IMG_1009.jpeg

    IMG_1009.jpeg

    • mangoelectrics
    • Media item
    • Comments: 0
    • Category: Electrical Videos
  4. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    It is now working! STOP arguing please! THREAD CLOSED
  5. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    THREAD CLOSED
  6. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    THREAD CLOSED This issue has now been resolved. Here is the final working schematic:
  7. Screenshot 2025-03-25 at 20.15.19.png

    Screenshot 2025-03-25 at 20.15.19.png

    • mangoelectrics
    • Media item
    • Comments: 0
    • Category: Electrical Videos
  8. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    Thanks, let me explain a bit further. According to the video, mine are no good. They have measurements of between G and K: 138 Ω K and A: 63M Ω and always rising A and G: 76M Ω and always rising I am building a coil accelerator and so am needing to use the thyristor to switch on the coil when...
  9. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    @Moley Do you have any suggestions? Thanks!
  10. mangoelectrics

    12VDC to 3.3VDC Stepdown DIY

    As @Moley said I would just get one of these: Aliexpress.com Ive purchased numerous of them before. Can't get anything better for the price and SO easy to set up. You will only need a multimeter. Hope this helps!
  11. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    Also, when I remove the 1k resistor from - to gate then power the gate with + 5v the motor immediately runs, but does not continue to run after I remove the power to the gate, it should continue to run as I have permanent power to the K and A of the thyristor. Im beginning to think my...
  12. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    Just tried that now. It does work as you say it should although it takes the positive power in through the gate pin and does not seem to activate the thyristor. Do you know why this might be? Thanks again!
  13. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    Will try this in the morning, thanks for your help!
  14. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    Thanks both of you. That’s very helpful to know for sure which is which. If I put - to the gate then the led or motor immediately is powered continuously even without the negative lead going into pin 2. Hope this helps.
  15. mangoelectrics

    UK 70TPS12 Thyristor - Help!

    Can you tell me which pin you think is the gate? 1, 2, or 3? From the photo I think it’s pin 3, but thought I would get a second opinion. Thanks!
See more

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Green 2 Go Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses Heating 2 Go
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

TrueNAS JBOD Storage Server

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
Plumbers Forums | Plumbing Advice | Gas Forum
Back
Top