Recent content by stewartrossinv

  1. S

    AFDDs for single-socket circuits

    The analytical team I managed until I retired from the Scottish Fire and Rescue Service were (and are) responsible amongst other things for publishing comparable fire statistics for Scotland. The stats you kindly quoted are derived from data completed by all fire and rescue services in England...
  2. S

    Heating blanket controller

    Attempting to replace a 240V power controller on a safety-critical item such as an electric underblanket without knowing how the original controller was built is not something I would recommend. Before I retired I was a stats person for the second-largest fire service in Britain. Although it is...
  3. S

    Power over Ethernet

    I have been experiencing similar issues with my devolo network adapters, which until recently had been working perfectly. I find that several times a night on occasions I am losing internet access - and the only solution is to unplug the adapter then plug it back in. I strongly suspect that the...
  4. S

    DIY help Hotpoint DD2 844C BL Oven power cable

    Whilst the the connections at the rear right of the oven are not accessible as long as the oven is housed in your kitchen units, anyone who removes the oven in the future would be at risk of contacting exposed live parts. For all the time it takes to do, it would be much better just to remove...
  5. S

    need an expert opinion on this connection

    It's fine as it is. According to a web search, each of your 19-LED clusters is rated at about 1.4W. The driver you have is rated at 5W, so the load is well within its rating. It's the correct voltage driver for the cluster, so there is no danger of overdriving the LEDs. Makes me wonder again...
  6. S

    need an expert opinion on this connection

    Yes, though it may be best to do so one at a time just in case one or other is indeed faulty. Make sure you get the polarity correct - that is, that you wire each of them to the output the same way as the one that works at present (plus to plus and minus to minus). -Stewart
  7. S

    need an expert opinion on this connection

    @DefyG and @Lucien Nunes both pointed out the use of the electronic Halogen transformer in place of a proper LED driver, and @Wilko, DefyG and Lucien have all mentioned the possibility of damage to the LEDs. The original installer has perhaps used what was to hand at the time, but it was a very...
  8. S

    Why have I no continuity signal here?

    All the best with your project Shawn. You've put a lot of time, effort and money into it - and your enthusiasm is clear to see too! -Stewart
  9. S

    Why have I no continuity signal here?

    Hi Shaun. The cables you linked look well made, though expensive! I have no issues at all with those cables vs those supplied by the OEM. If you remove the connectors on any of these cables yourself and fit your own you take responsibility for any subsequent failure (i.e. you invalidate the...
  10. S

    Why have I no continuity signal here?

    Hi Shawn. I guess you want to show off the innards of your computer as best as possible, hence the PET braided sleeving. I would advise that you do the minimum of cutting and reconnecting, as home-modification will potentially degrade the reliability of (normally excellent) commercially-produced...
  11. S

    Why have I no continuity signal here?

    The headphone cable you show is (in my opinion) very difficult to make suitable connections using DIY soldering techniques. The cable comprises bunches of very fine-stranded wires, each strand covered with an insulating lacquer. Because the strands are all insulated by the lacquer there is no...
  12. S

    New smoke detectors law

    The requirements to meet the new Scottish legislation (implementation delayed to Feb 2022 due to COVID-19) are listed on the Scottish Government website at https://www.gov.scot/publications/fire-and-smoke-alarms-in-scottish-homes/: Although smoke alarms in bedrooms are not required under the...
  13. S

    Shower pull cord switch melted new one not working.

    The switch appears to be miswired. You have a black neutral cable on the right wired to a connection which is marked L for live. Also, way too much copper showing on the leftmost red (Live) cable, and some damaged insulation on the leftmost neutral (which may be to the wrong terminal anyway). I...
  14. S

    Electric hob

    Oh dear. If this is indeed a freestanding cooker, someone's taken what should have been a simple install (via the connector plate at the rear of the cooker) and made it hugely complicated by taking the hob off the cooker and accidentally parting the internal connections from the thermostats etc...
  15. S

    Temporary lights out after rainstorm

    Hope you can get the rats caught and eliminated. They can cause severe damage to your wiring, and I'm sure your electrician will be able to replace whatever they've chewed after they've been caught. Thanks for the update!
See more

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Green 2 Go Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses Heating 2 Go
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

TrueNAS JBOD Storage Server

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Outside Play
Back
Top