array

Recent contents Top users
  1. T

    sizing 3 phase supply to/from 50KW solar array

    Hi all, I have been asked to run a 3 phase supply from a nearby service head to a new DB servicing a solar array to be fitted on a riding school roof. This is to take the electricity generated back to the grid. A proper MCS contractor is doing the array. The problem I have is that the array is...
  2. K

    East/West Array DC cable run

    Hi I have just had a job in to fit 16 panels split into 2 banks of 8 east/west facing. Inverter position is near the west side of the roof. The building is a barn conversion and has all the internal ceilings vaulted up to the ridge ie no loft space. Does anyone have any bright ideas as to how...
  3. S

    Array Frame Bonding

    Hi all. Have always kept clear of transformer less inverters due to the need to bond the array however we are about to install several SB3600-TL's as they are predicting great yields etc. How have you guys gone about bonding the array etc? Any special bonding clamps/fixings due to location...
  4. Mark42

    Sizing DC cables, PV Array to Inverter. Confused. Help please!

    My brain is overheating trying to make sense of PV panel parameters and calculate the CSA of a DC feed cable to the inverter. For my 16 HL Solar 250W panels, the spec is: Imp 4.94A Vmp 50.6V Isc 5.35A Voc 60.5V Two strings of eight panels in parallel. Therefore: Total current at max power =...
  5. O

    Ballast Calcs - flat roof array frames

    Sorry if this is out of place here... But any advice from real world experience would help. Rather than designing PV system using off the shelf mounting systems like Consoles for example where the ballast requirements can easly be ascertained from the installation manual, I'd like to explore...
  6. D

    Ground mounted solar

    Would you know the advised distance between solar frames on a ground mount system Ie one system directly behind another? The back of the first system is 1900mm affl and the next system behind this should be 9000mm away to clear sunlight at 12 degrees in decemeber (its in scotchland!) But that...
  7. D

    split a single string pv array in to 2 using a splitter

    I am a solar installer and i have been told that i can use a mc4 splitter to connect 1 string in to both connections on inverter as they had done this before to spread the load surly this can not be right. as a splitter is used for 2 strings going in to 1 not the other way around
  8. S

    DC Array cabling

    We are designing an install whereby the DC string cables need to come back from the middle of a garden to the property. We plan to install 6mm 4 core SWA cable to carry the load (2 strings) and wonder whether the armouring of this SWA cable needs to be earthed as in an ac application - the Regs...
  9. G

    Array size,Inverter size, what do i put on fit application

    HI all, Im installing 16 x 240w panels and a eversoler 4000tl, so i have 3.8kw system, whats the maximum allowed i read somewhere 3.68 so what do i put on the FIT application and when notifying the DNO.?? thanks Grand
  10. B

    3kw split array with an aurora 3000 - is it working correctly ?

    I have just had installed a Aurora power one split invertor and have 6 250W Solarworld panels facing east, plus 6 facing west. How do I know if both sides are working correctly ? I have no manual on the Aurora but from the panel readout I assume that PIN 1 is for one set of panels and PIN 2 is...
  11. M

    Dti Guide..... When will it be released??

    Hi, does anyone know if there is a proposed release date for the 3rd edition??
  12. M

    connecting array wired by others

    we're gonna be doing the ac work, and possibly connecting strings at inverters, on systems where other contractors will be installing the modules, and feeding cables through to us. or they may already have fed the cables through to inverter location! how can i be certain i'm observing correct...
  13. C

    Why a SB 3000TL-20 for a 4kW array?

    My installation has just been completed. I have 16 x Hyundai HIS-250MG panels connected in 2 x 8 strings to a Sunny Boy SB 3000TL-20. This inverter and configuration is as recommended by Sunny Design. However... The evaluation of design sheet gives PV peak power of 4.00 kWp, max. DC power of...
  14. R

    2 properties, 1 array

    Hi all, I've been asked to quote for a system where the array will span the whole roof space of 2 semi detached properties. The same guy owns both properties and rents out next door so he owns both roofs. All the electricity generated will be fed in to the house he lives in. The guy says he has...
  15. C

    Different watt panels same array?

    Firstly under normal circumstances i wouldnt even entertain this idea and have already advised against it. However... Is there a problem with installing 4x 250w modules and 10x 240w panels on the same array, same inverter? Will the 250w just lose performance or will the whole system be...
  16. G

    circuit advice

    can I check this ground mount system circuit with some one please. Henley block out of tails feeding existing board from cut out to include a small garage consumer unit with a 16A RCBO. AC isolator, generation meter, 6mm2 two core SWA (60meters) to AC isolator - Inverter. Earth inverter as...
  17. P

    Array frame earthing

    Having read the draft PV guide edtion 3 out for review, I see very little instances where you would earth or bond an array frame. I appreciate there are instances where you should but these seem quite rare reading the new guidline, even with transformerless inverters. is anyone still earthing...
  18. D

    3kw split array with an aurora 3000 for 9400 is that reasonable?

    Im getting a system installed with what should be a split 3kw ( 12 suntech 250's) with what should be an aurora 3000 inverter. one half is south east the other is west. It includes scaffolding ect. Does this sound ok? and is there anything i need to be careful about for the install. Im not that...
  19. B

    TL inverter & array frame bonding..confusing at best!

    Hello! I am putting in a 4Kw ground mount scheme with a TL inverter and I can't make sense of the DTI earthing tree. Framework to be of unistrut construction, and effectivley insulated from tera firma by concrete. The main incomer is PME, and if I follow the DTI tree, the end result is that I...
  20. A

    RCD tripping

    Hi All, First time for this so unsure what could be the cause. CSUN 250 panels - string of 16 connected via 4mm DC cable to Fronius IG TL 4.0 feed to CU via 2.5mm T+E DC cable run including the array is 22m and the AC run is 12m. Random tripping of the RCD, AC circuit is okay continuity and...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Workwear Shropshire
Top Bottom
Back