branch
-
D
How to remove a branch of a 3 gang
Hi all. In our lounge we have a 3 gang light switch. One switch switches the ceiling light, 2nd switch switches a pair of wall lights, and the 3rd one switches a picture light mounted above the fireplace. Ironically, I may need to remove the picture light to make way for a large picture. So my...- DIY Phil
- Thread
- 3 gang branch how to remove
- Replies: 5
- Forum: DIY Electrical Advice
-
R
DPDT switching branch circuit from one breaker to another?
I’m planning a 240V welder circuit in a detached garage with a 100A sub panel. For the 160A or 180A output welders I’m looking at, the conductor can be #10, and a 30A breaker is probably OK, but a 40 would help the duty cycle. Conductor must handle welder's 1eff rating, breaker can be up to...- rmully
- Thread
- another branch breaker circuit switching
- Replies: 5
- Forum: UK Electrical Forum
-
P
Is 8awg ok to use for a branch circuit (30amp leg) ?
I wanted to ask if 8awg (stranded) was safe to use for residential? I am wanting to run a branch circuit from my main panel to the garage (about 15ft away) into subpanel. Actually it's a 70amp Eaton 2circuit loadcenter. I dont have anymore room in my current Main panel so Ive read on here how...- PorterKozak99!
- Thread
- branch circuit screwfix
- Replies: 4
- Forum: UK Electrical Forum
-
M
Strange lighting issue
Had 2 new lighting groups installed on a multi wire branch circuit that used to be used for kitchen outlets. The 12-3 cable enters the switch box where the neutral is tied to the 2 neutrals from the lights. Hots go to 3 way switches with travelers sent to 3 way dimmers in another box. Hots are...- mhunter
- Thread
- branch issue lighting strange
- Replies: 2
- Forum: UK Electrical Forum
-
R
Power Panel Changes Voltage with Branch Circuits
I have a Single Phase Power box for a townhouse. When I read voltage across the Hot legs (A) and (B) to ground I get 123 volts with the main breaker turned off. With all the circuit breakers turned off and powering up the main breaker to the panel I still have 123 volts across both (A) and (B)...- Rededdie
- Thread
- branch changes circuits panel power screwfix voltage
- Replies: 1
- Forum: UK Electrical Forum
-
F
Running branch to shed
I want to do a run to a subpanel in a shed - about 50'. 3 circuits: lights, electrical, spilt. I have an isolation panel - can this be retrofitted with a subpanel circuit to branch off to the shed?- flownerbuilder
- Thread
- branch running screwfix shed
- Replies: 2
- Forum: UK Electrical Forum
-
S
No Volts on Branch Circuit
Hello all, As a member of various other Forums I understand that after reading the “guidance sticky” (done!) I should use search to see if others have shared my situation. Gonna pass on that last step (the Auto-search on my question was a nice touch) and get right to it. I have a small shed...- Stevewaclo
- Thread
- branch circuit volts
- Replies: 8
- Forum: DIY Electrical Advice
-
D
Code regarding main and branch breakers
I’m looking to add a GFCI breaker to my main panel. I have several open slots and have not reached the circuit capacity of my panel. However, the main breaker is not located at the top of the panel. See picture. Is there any reason (code or otherwise) I can’t locate a circuit breaker above the...- doubleAbrew
- Thread
- branch breakers code main regarding screwfix
- Replies: 7
- Forum: UK Electrical Forum
-
G
firefighter branch of military service
I know that this is a pipe dream but i was thinking about the fires in california and i know they have problems like this in other countries! maybe its time we suggested to our governments to form new branches of military dedicated to just firefighting. if a fire is too big for local depts to...- gnuuser
- Thread
- branch military service
- Replies: 8
- Forum: Electrician Talk
-
F
Feeder and Branch separation point
Hi, could some one please explain to me the point at which the feeder stops and becomes a branch on the attached drawing. This is really bugging me and if I had hair it would all be ripped out by now and I am struggling to under stand. Anyone's help would be most appreciated. Thanks in advance- freakydeakie
- Thread
- branch feeder point separation
- Replies: 5
- Forum: UK Electrical Forum
-
I
Voltage Drop Branch of radial circuit
hi guys Need some help in calculating voltage drop on a branched radial circuit. (13A design load 2.5mm cable)( cu to junction box 8m 2.5mm) for a standard loop in loop out radial it would be IbxDxmV/m/1000 this circuit has 2 branches from the junction box one/ 10m long ( 1 double...- ianphilip007
- Thread
- branch circuit radial radial circuit voltage voltage drop volts
- Replies: 4
- Forum: UK Electrical Forum
-
D
For your entertainment .... HV + Branch = nice display.
LiveLeak.com - Tree branch falls on power lines - high voltage - Wicked Effect Its short but entertaining to us sparks just a reminder of the dangers these voltages carry.:grin:- Darkwood
- Thread
- branch display
- Replies: 3
- Forum: UK Electrical Forum
-
P
Branch circuits to buildings
Hopefully a quick and easy one... Ive had a look through the regs but the only version this company give us is a .PDF format and its really annoying trying to look through it on the computer so hoping one of you Reg masters can help me out. Right...For example lets says we have four...- pauljpickering8
- Thread
- branch building buildings circuit circuits
- Replies: 21
- Forum: Electrical Wiring, Theories and Regulations
-
J
Branch Connectors
when using branch connectors in an array, for example 2 strings of 8 and the positives go to one branch and the negatives to the other one, there are only two cables going back to the inverter, does this mean that the same laws apply if branch connectors weren't used: amps double and volts dont?- Jie
- Thread
- branch connectors
- Replies: 6
- Forum: Solar PV Forum | Solar Panels Forum
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
