Hello folks
Does anyone know if it's possible to connect a pair of bathroom wall lights - the type with an integral pull cord for switching the light on and off - so that the pull cord on one fixture will control both fixtures? I'd like to have this type of setup so I don't need to have 2 pull...
hi all
im building a garden shed andd want to put power to it. I want to do it myself and will be including it in my building notice for the labc to check.
I will be using 6mm 3-core swa which will be about 50m from the consumer unit, but I have some 6mm t&e able already from the consumer...
Hiya
I've found a power supply circuit called TB008 that doesn't use a transformer and connects Ground and Neutral together. Now first of all, I'm no electrician, but everyone I've asked seems to think this is odd. Can anyone confirm?
From reading around it seems like the Neutral and Earth...
everytime i connect my computer to electricity it makes a spark ,why?
actualy i have a cord an when i plug the second thing in , it makes the spark .
The secod thing is the monitor or the computer.
Is this bad for my computer or for the monitor?
fmariusd
Thread
aus
computer
connecting
electric
electrical
electricity
Apologies if this is not the right place for this post.
New build extension with electric Warm Up brand underfloor heating in 1 room; about 6m which I think is only about 750w. Electrician connected temporarily via an 13A fused switch (there is also a circuit breaker on consumer unit). There...
Hi All,
I have a few questions and would like your opinion and advice on please, recently housed local to us have had a power outage for 30hrs, and this got me thinking (dangerous I know) about using a generator to feed essencial circuits.
The house supply is TN-C-S
Crabtree Starbreaker...
Hi all - just wondering if I could get some advice.
I have installed 3 new circuits in an extension - a kitchen - lighting, ring main and cooker (gas so just 13A elec start). The existing board only contains MCB's, and my new circuits need to comply with 17th edition regs, so need RCD...
sambuca2907
Thread
aus
connecting
consumer
consumer unit
question
unit
Can anyone explain why on a split board (RCD+NON RCD) That the RCD neutral has its own neutral bar? When in fact if you were to follow the neutral cable, they all go back to the same source anyway??:confused:
Picture lighting help for above dartboard. Connecting a plug
Hello all , iv just joined the forum & was hoping to get some help on wiring up a picture light, hopefully after a while ill be able to give something back to the forum :). Anyway im putting a Picture light above my dartboard,ill not...
CableGuy180
Thread
aus
brown
connecting
earth
help
light
lighting
picture
plug
I dont have much experiance with heating systems at all, So new to me.
Been to a job where a plumber has fitted a new boiler.
This is a link to the exact boiler and its connections... CLICK HERE http://www.biasi.co.uk/pdf/Riva_Compact_HE/USER___INSTALLATION/3505_EDITION.pdf
I Have a 5...
hey, i've just changed an old fuse board! i had to change the mains cable as it was too small, so when reconneting it there was no earth terminal on the meter! i have a cable going to an earth rod! but someone told me i should connect my mains earth in the meter with my mains nuteral, he called...
can someone help me answer this question?
describe the factors affecting the choice of wiring systems and cable? with reference to cables connected to bus bar operating at higher then normal recommended temperaturess for the cable.
cheers phil
Hi all, I’d appreciate some advice on fitting a new wall light (not bought it yet but want to know options for fitting).....
The new light is designed to be wall mounted but has a plug for supply from a socket. However, I’d like to fit it in place of an existing wall unit which is on the...
:confused: Hello all,
I am a gas fitter and a domestic installer (limited scope) and was wondering what testing i have to do to install a spur (to fit a boiler) to a previously installed ring. Do i have to test the ring from the start as if i have installed it myself?
i have replaced a 415v 3 phase motor at work. The old one had 3 terminals in a line, each with one internal wire connected, and one terminal on other side with 3 internal wires connected. The new one has 6 terminals, each with one internal wire connected. It came with 3 bridging links which i...
lkpflk
Thread
3 phase
canada
connected
connecting
delta
links
motor
phase
phases
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.