existing

  1. Tink

    Moving two existing sockets with no RCD

    Just completed a site visit regarding moving two existing 13amp double sockets further along the wall (Chasing out, reinstalled, re-plaster etc. how lovely!) However there’s no additional protection provided by RCD as the CU is too old and the client doesn’t won’t to upgrade due to cost! Advice...
  2. S

    Earthing for solar off grid system

    Hi All Planning an off-grid solar system and I’m pretty confident about most of it except for one thing - earthing. I believe the inverter I will use, a Victron Phoenix 12/350, has a floating earth - so there will be 230V L-’N’, 115V L-E and 115V ’N’-E. The system will power an existing (old)...
  3. W

    Breaking Existing Ring for Garage Conversion

    Hi, I'm in the process of converting my garage into a utility and living area. Currently the garage has 2 sockets and a switched fused spur that are part of the upstairs ring main. This ring main serves the upstairs bedroom only as it's classed as the 'Extension Ring Main'. It was installed as...
  4. U

    How to extend ring main and where to channel cable (Domestic property)

    Hi all, My daughter has asked me to put in a new socket for her. She would like it putting about 10ft from an existing double socket on the same wall. The floor is concrete and her upstairs has just been decorated (carpets etc) so I searched to see if it was acceptable to run mains cable behind...
  5. S

    Trouble with an existing Pv system Schott Asi 105w panels

    Hi Guy after your best advice, been along to see a customer who is having trouble with his system which has been up and running for just over Four years and the original installers are no longer in business. He has approx a 17kw system of Schott Asi 105 w panels on the roof Appox 162 info...
  6. Soulsurfer

    Adding PIR sensor to existing outside light.

    Hi I am needing to adjust a 1 way switched outside light at a house in a couple of days to switch 2 way possibly with an ip rated switch on the way to the front door as it's only switched 1 way from inside the porch at present. I'm just thinking of instead of an exterior switch of using a...
  7. mrhorse

    Amendment 3 RCD question...

    Hello everyone, Just getting familiar with the changes to BS 7671 brought in with Amendment 3. I have a question regarding Regulation 411.3.3 in particular. The Regulation states that an RCD should be provided for socket-outlets with a rated current not exceeding 20A for all installations...
  8. J

    Roller shutter door motor wiring diagram

    Hi We are looking to replace an existing roller shutter door motor with the below Garog motor and wondered if anyone had a wiring diagram for this? Make: Garog Type: ULA25EE V 400 A 1.0 KW 0.5 RPM 28 PH 3 HZ 50 IP 44
  9. C

    Testing new floorboxes plugged into existing electrak

    Hi, We are adding some floor boxes onto an existing electrak in an occupied office,could anyone comfirm the tests we have to complete,only i've been told its classed as a plugged in appliance so doesn't require any tests.Is this correct?

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock