uHeat Banner - Forum Discount Available
This official sponsor may provide discounts for members


  1. EricMark

    Hive software options?

    This is how I think one would need to wire Hive on the very old C Plan which has no tank thermostat, however I have been told on another forum the relay is not required, and it can be configured with software to switch pump and boiler with central heating and just boiler for domestic hot water...
  2. B

    Hive dual zone

    I have been asked to fit a hive multizone thermostat system on to a dual zone central heating setup.. The components are... Logic heat 12 boiler Honeywell st9100c single channel controller Honeywell cm07 wireless stats.. Looking at the current wiring (see below), it appears theres only one...
  3. R

    Wiring a 2 port valve on a hive system

    Good afternoon Im in need of some assistance on a job. A new central heating system is being installed (previously storage heating) and the customer has purchased a hive multizone kit. She wants to control her heating up stairs and downstairs seperate so would need zones valves installed. I...
  4. J

    Changing salus receiver to hive

    Hi i need to change my old salus receiver to my new hive one and im not sure about the wiring do i put it all the wires in the same places on the hive receiver? The picture is the wiring into the old receiver
  5. F

    Need help wiring up hive receiver

    I have wired up my Hive receiver to the boiler and have also signed up to the app. On my app when i turn on the central heating the light on the hive receiver for central heating comes on showing green solid, however the heating does not turn on although the light for the receiver is on...
  6. S

    Vokera Linea 24 combi boiler - Hive wiring help

    I'm trying to install a hive thermostat. I was able to get the hive receiver hooked up but I think I've made a mistake with the wiring as the heating will stay on continuously. Can anyone tell me what needs connected to what? I've attached the boiler board (It only has the old timer connected...
  7. T

    Domestic Help with Hive to Tado wiring

    Hi guys, I’m looking for some help... I have a Worcester Bosch CDI combi boiler that’s connected to a Hive radio thermostat that doesn’t control the hot water and doesn’t connect to the internet, smart phones etc etc We have purchased a Tado Smart Thermostat and Extension Kit to replace the...
  8. F

    Fixing a TWO Hub HIVE system (in a single house)

    Over the course of getting the full house replumbed, a combination of our sparky and plumber have fitted a hive installation. The installation consists of two hubs, one which controls hot water and downstairs heating, the second controls the upstairs heating (over two floors). Each hub has its...
  9. D

    Hive lighting question

    Hi there, I hope you can help me please. I have ordered some Hive smart lights. Tech specs of these are here: Hive Active Light - Cool to Warm White Smart Light Bulb - Tech Specs | Hive Home - https://www.hivehome.com/products/hive-active-light-cool-to-warm-white/tech-specs In short they need...
  10. R

    Wiring a Hive receiver to a Vokera Linea Combi boiler

    Can anyone please help me to wire a Hive to a Vokera Linea Combi Boiler I have uploaded diagrams and pictures of everything I think is important. I think I should 1 Disconnect the Honeywell thermostat and bridge the two connectors where it says Room Thermostat on the wiring diagram. 2...
  11. R

    Hive receiver installation on Vokera Compact A Combi

    I'm trying to install a hive active heating into a Vokera Compact A Combi boiler. I think I understand the principles of the system but am looking for support on wiring the receiver to the boiler. The boiler electrical diagram can be found here http://qr.vokera.co.uk/qr?code=20099226 (figure...
  12. B

    Installing hive Worcester Bosch

    Hi all, I’m hoping someone would be able to give me some advice on Hive heating. I have a Worcester Bosch Greenstar 30si with built in timer (however I understand this is an option that can be removed). I would like to install Hive but have no idea how to go about it. I would consider...
  13. J

    Hive install with Mainslink pro installed

    Have had the Mainslink Pro installed with the timer now out of action (communication cables were cut, so used the mainslink to RF the signal from boiler to airing cuboard, where all other equipment is stored (pump/tank ect.) Hive chap is coming in 2 days and I wondered if the hive would work...
  14. L

    Another HIVE thermostat wiring issues

    Hello All, New Hive thermostat has been installed. When you run the hot tap the boiler kicks in to produce hot water. However when called to heat the rads it will not kick in to produce any heat. I expect it has been wired up incorrectly. From the fused spur I have....... L N E From the...
  15. J

    Permament Live to Hive multizone

    Hi, im having issues with my hive multizone and getting power to my upstairs receiver. I have 2 zones, upstairs and downstairs. I can only get power to my upstairs receiver when my downstairs heating is on. I have installed a loop wire between live and common in my receiver upstairs but...
  16. A

    Help to wire up hive single receiver to valliant.

    Hi all, Firstly, I apologise for asking for help but I’ve been massively let down by a plumber. I’ve had a new valliant ecopro 30 installed. It’s got 2 zones (2x 2 port valves) 1 for UFH and 1 for Radiators. The plumber has not wired anything and the electrician is struggling now. He’s wired up...
  17. haptism

    Hive heating question

    Im not familiar with Hive heating systems; although I am aware that somewhere along the line (probably at the start, and not the control box thing that plugs into socket!) it needs a mains supply . Anyone know if the Hive circuit is switched off, would this cause the boiler the revert to its...
  18. M

    Hive Install - Worcester 24I RSF

    Hello all Took the plunge an have gone for a Hive setup. Boiler has a mechanical programmer fitted an no other wired/ wireless stat fitted Removed the bottom panel of the boiler an can see the main feed on the far left. Then its currently wired as CN CI CL all of these go to the mechanical...
  19. C

    HIVE - UT1 programmer and ES1 Thermostat wiring issues

    I have a British Gas installed Worcester 28i boiler with a UT1 programmer and ES1 Thermostat and trying to replace the UT1 and ES1 with Hive. ES1 The wiring for the ES1 is 4 wires Brown, Blue, Black and Green/Yellow. the black and yellow/green wires have red sleeves near the end. (All 4 wires...
  20. J

    Hive conversion on Potterton oil boiler - heating only

    Hi Gents, after some advice on what should have been a relatively simple conversion, but I am hesitant due to lack of boiler experience. Have a Potterton floor standing oil boiler - supplying heating only, currently has Smiths controller, frost stat (possibly) house stat, pump feed and wired as...
  21. polo1

    Hive or Nest....what's your preference?

    With all the recent posts about "how do I....." on these systems and as the title, if you have been installing either or both of these control systems, do you rate one over the other?
  22. J

    How to install HIVE 2 with worchester 28i junior from Honeywell bdr91

    Hi there, I'm trying to install my new HIVE 2 but having some trouble with the wiring and hoping someone can help me? Here is my current set up : I have a honeywell bdr91 wireless receiver and a separate honeywell thermostat both situated next to the boiler at the side of the house as shown...
  23. N

    Hive receiver connections to Vaillant boiler

    I have a Vaillant EcoTec Pro 28 boiler and a Vaillant mechanical thermostat (unsure of the precise model) and I’m thinking about installing hive to be able to access the remote switching feature and also to able to place the thermostat where I want it rather than where the installer thought it...
  24. Jamie'

    Hive single channel receiver wiring

    Hi all, Looking to wire up a hive receiver but never done one on a job before (just finished 4 year apprentachip flat/house bashing mainly) so just want to check I'm going to be doing it right before going ahead. So i was going to run a 3 core T&E from the boiler to the receiver. So at...
  25. M

    Hive wiring for Glowworm

    hi to you all,new today.May I wish you all a happy and peaceful New Year. Have been presented with hive active set,don,t know how to connect.Have a glowworm30 cxi .Control thermostat only has a black wire connected toTerminal RT and a brown connected to live. Connecting...
  26. M

    Hive 2 to Ariston Microgenus

    Hi all, I have just bought a Hive 2 system to go with my Microgenus HE system. There is no existing external control system/thermostat and was all controlled by the internal timer, which can’t keep time. I think I’ve worked out the wiring but just want to check with you guys first as there are...
  27. D

    Hive Active Heating 2 Wiring HELP

    Hello, Ive been reading through these forums and thought id post to ask for help. I have the hive active 2 and am a bit stuck. attached is the have backplate which i need to wire but also below is my boiler thermostat wiring. 1, 2 and 3 on the backplate are common heating off and heating on...
  28. T

    Hive system playing up any ideas?

    So my son has a hive controller and while it appears to say system is on the boiler does not switch on. Sometime later, maybe an hour the boiler switches on. Any ideas ? It is a potterton boiler quite old and the hive has been tacked on, perhaps wrongly. Anyone in the Farnham Surrey area that...
  29. jedder

    Fitting Hive 2 to a oil boiler in Spain

    Hi all, Can you help, I have bought a Hive 2 active heating (heating only version) to replace the thermostat we have in spain, Its an oil combi boiler (Tifel - Eurofel 40 See pic) The exising thermostat / control only has 2 wires goin to it from the boiler (see pic). Can someone give me an...
  30. Jsguk

    Hive Worcester Bosch installation help!!

    Hi All, Hive Worcester Bosch RD532i Boiler and TR2 thermostat. I am replacing the TR2 with the Hive 3rd gen Link and Thermostat, The boiler has 3 wires connected to the existing therm, Which ports in the Link do i connect the 3 wires to, or which wire do i lose? I have attached photos for you...
Top Bottom