want to get a cheap earth loop tester for work,just something to leave in toolbox I have one of those Kewtech socket testers with earth loop lights on it but want something that actually gives a reading,will be using my mft for main tests this is just to keep an eye on things with in between...
Hope someone can help, I am an industrial biased electrician & a friend has asked me to check an outside tap on one of his houses where the tennant keeps getting a belt off the tap, the loop test at the board shown up 17.8ohms & was registered as dangerous on the tester (A Metrel tester)...
The...
hi guys,
Just wanted some help with some course work for college. Any help is greatly apprecitaed.
Why should a low value earth fault impedance should be achieved for all circuts?
thanks
Ryan Kavanagh
Thread
current
earth
earth fault loop impedance
fault
impedance
looploop impedance
value
I fitted a new circuit, upon testing, the EFLI was 1.29 ohms on a TN-S system.I rang up the DNO for advice, and was told that is an emergency, we'll be there within 2 hours.There was no point me hanging around, so I went to my next job. I caught up with the houseowner today, and asked what...
Got called out yesterday to a blown BS88 fuse on a ring circuit.
The customer reported a big bang when plugging something into a socket.
The result was the cheap socket was faulty.
Anyhow whilst I was there (I did not really like the quality of the install) so I did a full test on the ring...
Hi,
Our main fuse from the power distributor blew and Western Power attended and replaced. During this visit they established that their was a problem with reverse polarity and that when the RCD was installed the tails in the grey twin cable were connected red-black in the top of the consumer...
Maverick777
Thread
earth
impedance
looploop impedance
power
problem
supply
test
Hi Guys,
The 17th edition gives you a table of circuit breakers and their maximum allowed Zs, however as the 17th edition does not cover "machinery", we have just started working with BS EN 60204-1 "Safety of machinery - Electrical equipment of machines - Part 1 General requirements", and this...
markymark31
Thread
earth
loop
machinery
machines
required
standard
table
testing
times
While doing the r1 and r2 loop test on a ring main they always say at least the r2 too be a larger reading than the r1, because of the cable size difference?.
why is the earth reading higher, I thought the bigger the area of the core, it would have more resistance than that off of 1.5mm earth???
Hi
Happy new year to everyone.
I have mft1720 with megger fused leads protected by 50mA fused.
On Zdb (not main but garage unit) I wanted to do a Z measurement, set it to high current mode (L-L/L-N and Z) when I attempted to take a reading between live wires it blew the fuse in the Netural...
krishcanag
Thread
current
fused
issue
leads
loop
megger
order
something
test
Has anyone else had the problem of it tripping rcds on non trip loop?? seems only wylex in my case.
I have spoke to megger to be told i was performing the test wrong! Quite rude tbh.
I have since spent a lot of time thinking about it and the external earth fault path it takes...
so i have tried...
Is the any reason why you shouldnt fit a two gang switch, one wired as standard (switched live with 2T&E), and the second switch looped with the L-N passing through the switch (neutral in a wago). This second circuit is to power 5a sockets.
Would it be preferable to take a permanent live into...
jase31
Thread
light
light switch
lights
likes
loop
neutral
standard
switch
switches
through
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.