Hello everyone,
After abit of help I have done my compex 1-4 and 7&8
I went to a private/commercial property they use the pump to sell the fuel for park time racing events but the tanks and pipes where installed before 1974 so am I correct it doesn't need a area classification or is the the...
Hi all, first time poster :)
trying to figure out the british naming conventions on electrical components, and in need of help to identify the name in the UK, so here goes..
I have a single speed 1hp pool pump with a sal****er clorinator that requires to be run for 2 hours daily to keep the...
Hi All,
New here and a bit of an ask but I'm trying to control a CH pump using two Delta Dor wireless controllers.
The attached wiring diagrams show how we wire a single zone, single Delta Dor, single zone valve and how I propose using two Delta Dor controllers from two separate zones/zone...
I just bought a 12 volt tyre compressor and the instructions say connect it directly from the battery. The pump worked well but when I disconnected it the wires were very hot. Does this mean that the wire is not sufficiently robust?
BML
Thread
allow
battery
compressor
direct
pump
vehicle
wire
wired
wires
I have an MK panel with time clocks for pump and boiler. These are mechanical with tabs to set on/off times. One has failed and I just cannot find a supplier for a replacement. Anyone got any ideas?
heading to a job tomorrow and have been told the pump for the central heating is staying on all the time?
anyone ever come across this issue before? pretty sure its a "s" plan heating system with motorized valves!
any info appriciated!
Hi there,
I am a newbie to this forum, i am a fully qualified electrician and have recently passed my FICA 17th edition regs etc, (December 2014), however like many of us, i am still learning.
I'm after some advice regarding fitting a new shower pump.
A friend is replacing an electric shower...
Hi
i am working for a boiler conpany wiring their systems, i have come across a c plan and the new boiler they have installed has a pump over run now with connecting that up as i see correctly the boiler is permanently on due to the pump over run and heating all being connected together.
Is it...
Is it OK to wire a dedicated UF heating pump to the switch live from the programmer to the Zone valve (usually brown) as I can't use the switch live to the boiler (usually orange) or it will fire up other zones when not required. I am worried about pump operating slightly before the UF heating...
Hi All,
I'm installing a building management system in a domesticproperty with UFH and sorting out the temporary lashed-in control system. Somewiring centres (like the Emmetti) have a manifold pump delay, and some like theheatmiser don’t.
Is it essential to have, or can a Grundfos UPS2 pump...
Worcester has got me interested in finding out more about an air-water heat pump. Needs to be suitable for a property with 200m2 total floor area. Does anyone out there have any good experiences or recommendations?
Diagram attached shows what I believe could work for a well pump used on a farm. Basically the pump has been burning out and I have found the cause, its because they turn the pump on then forget and the water runs out in the well thus its dry pumping. So i was thinking of introducing this sort...
Recently notice a drop in performance of one of my heat pumps used for heating hot water.
The normal temp rise through the HP is around 8 degrees C but has recently dropped to around 3 degrees C.
The pressure guage shows approx 100psi with the HP OFF rising to approx with the HP ON but I don't...
anyone know of any regs stipulating requirements for positioning of a socket behind a bar for a pump illumination to plug into?...sockets are RCBO protected...thanks
Trying to get a 2001 Renault Clio started but the fuel pump won't run.
When I turn the ignition on I can measure 12v for a second or so at the fuel pump plug. But the pump doesn't prime or do anything. I believe it should run the pump for a second or so to pressurise the the fuel rail, and...
hi
I have wired up various central heating systems, y-plan, s-plan, under flooor etc . but i will be doing an air source heat system. They have not yet purchased the pump, but i am on with first fixing and i am wanting some advice on what cables are needed before any of the plans / instructions...
hi
I have wired up various central heating systems, y-plan, s-plan, under flooor etc . but i will be doing an air source heat system. They have not yet purchased the pump, but i am on with first fixing and i am wanting some advice on what cables are needed before any of the plans / instructions...
Should the CH pump run constantly, my own one does, but a customer asked the question, its a oil fired combi, I wired the controls and the plumber signed it of as ok perhaps the client is just a wee bit anxious
Pict
Hello, I'm seeking some advice please. I'm swapping a like for like ? Salamander RCM1 pump. As the photos illustrate, the original pump has wired in two separate terminal blocks, one to the pump and one to a fused connector box 12 inches away.
The replacement pump came wired as shown, pre wired...
Hi Guys,
I am replacing an old Grundfos 200 series twin head pump with one of the new fangled EUP ones, now the old ones had terminals T1 and T2 which was an on board thermal overload so you could hook it up to a plain contactor control circuit, now looking at these new ones its like Concorde...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.