Hi
I've just moved into a flat and it has old brass downlights in every room, I also think a lot of them are halogen and not led so keen to replace them all.
Sorry if the pics aren't enough but based on the wiring I have, could I just buy new white led spring holders (not sure name!) and...
Hi,
I currently have halogen downlighting in bathroom each light with an individual transformer.
One of the transformers has gone now and I have tried replacing with a new one which I believe to be like for like however it seems to make the odd crackling noise.
Could this be due to being...
Hi,
So I've just started to install some spotlights in a room in my house, and I always thought to use 1.5mm T&E so I've wired them all up and I've come to connect the main line in and noticed that it is 1.0 T&E. Am I okay to link the main line to my daisy chained spots on 1.5.
Some more...
thedanburgess
Thread
build
circuit
house
new
new build
question
radial
spotlights
t&e
Hi,
I have moved into a house with a huge kitchen which has 12 Luxna spotlights about 3 years ago. Over time the spotlights have been failing and it's quite expensive to replace them as they are a sealed unit. My question is, can I replace all the lights with normal (change the led bulb when...
Hi guys can anyone recommend what spotlights to install in the shelves in my media wall. Jcc v50s are my usual go to for downlights but i think there a bit too big for something like this, i have been looking at the ansell prism pro mini but just looking to see if anyone has any other...
Hi all new here and hoping for some advice.
I had added a new room to my house and want to add new spotlights and a new switch to the lighting circuit. My house is 1990's built in England UK, and looped in at the ceiling rose so the bedroom next door has 3 cables going to it. I would like to...
Looking for a product recommendation from a pro.
I have a few spots on our ranch where I have motion sensor spotlights. I have conscientiously installed the best ones I could find at any given time. The last few sets I bought were halogen, all-metal, including the sensor head, and came with...
warning! im a DIYer, so don't know alot about electrics!
The current spotlights have a driver and no earth, they're connected to their driver with a 2 wire clip connector. The driver is then connected to the mains wires with a 3 pin clip connector.
The replacements are mains voltage (astro...
Hi all. I know this is probably a stupid question but this isn’t my forte and I’d rather not waste £20 unnecessarily so thank you for any help.
I have these specific lights which use “puck” connectors. There are a couple of slots spare.
Lovebay led Cabinet Lights Set of 8, Warm White Under...
Hi all,
Looking for 3 replacement screw on cyclinder light shades for a bathroom spotlight. I believe the spotlight I have is Float Brushed Chrome effect Mains-powered 3 lamp Bathroom Spotlight | DIY at B&Q -...
HI we have six spotlights in our bathroom, I went up in the loft today and noticed a lot of condensation on the roof felt i also lifted a couple of the floor boards ( chip board type ) to find them soaked with condensation which appears to be going up into the loft through the spotlights, are...
My problem is, I did the wiring for my outdoor spotlights, it’s to light up some trees, before taking it out , I tested it in the garage and everything is working, once one of the spotlight is coming close to the earth it cuts to power of in the house. Hopefully someone can help me with this...
Hi All,
Client called recently. Saying few spotlights not working, halfway all 3 of them, living room-kitchen only two works out of 15. Flat newly built, last inspection 2019. I've been told by client that bulbs gone more or less st the same time. There was nothing obvious as I've checked...
Hi
I have two lighting circuits of 5 x low voltage halogen with individual transformers for each lamp.. to try out the new 240volt GU10 LED's.. obviously after turning power off at the consumer unit .. I cut out the transformer on one of the lights and connected the new lampholder to the 240v...
Hi,
I have 6 spotlights in my bathroom, when I moved into the house 4 years ago I replaced all 6 with LEDs but they wouldn't work, turns out I could only get the lights to stay on if 2 Halogen bulbs remained (1 on each end of the bathroom). Recently one of the 2 Halogen bulbs has died and now...
kevin2222
Thread
bathroom
bulbs
halogen
having
issue
led
led bulbs
spotlights
Hi everyone :)
I'm new to this forum and looking for some advise. (By the way im not a professional, just a DIY'er with some experience working on electrics for DIY projects etc)
In the bathroom im changing my current Halogen spotlights to new LED down lights. The current Halogen lights are...
next one , lads, bathroom spots
outside of zone one.
above the 2250 , directly above the bath
ip and fire rated.
240v led spots.
existing installation not rcd protected.
hi guys
i am planning a rewire in a medium sized house. Lounge, dining room, kitchen and bedrooms are all going to be spots apart from the odd pendent over breakfast bar. i am looking for some quality spots that dont cost the earth!
also any particular preference over grid wiring or standard...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc