Hi,
I need to move a two way light switch from one side of a breeze block wall to another.....there isn’t enough length on the existing cable to feed it though. So I’m going to need to use electrical blocks to extend the cable, then feed the new length through. Do I need to use an electrical...
We are going through a building (now unoccupied) to identify from old drawings and what circuit charts there are to prove what does what before safe isolation to do alterations and remove. We are doing this for the ground floor however the boards are in the roof area. To do this we are using 2...
Right. My Son wanted me to change his light switches which generally isn't too much of an issue, until I came to replace the double rocker double two way switch at the bottom of the stairs. Just to clarify, one switch is for the stairs, and one for the lounge lighting. Both of which are two way...
Hi Chaps,
Re: The picture....
Is the Brown Wire that goes in to L1 on the second faceplate a permanent live?
If so, could I change the faceplate to a 2 gang and add a link from the L1 to the Comm to feed another lamp?
Thanks,
T
I've installed a number of dimmable LED downlights switched two ways. They're switched by one dimmer and a standard rocker.
When they are switched on with the dimmer the lights operate normally and can be dimmed however they seem to override the other switch which will not switch the lights off...
If your bored or like a challenge I thought (maybe wrongly) this might be interesting to trainees and maybe others. As the title convert three way switching to two way (Sw 2 + 3) danlers time lag (Master and slave) using switch 2 and 3. Assume you cannot find the junction box. Can it be done...
The Ghost
Thread
conversion
interesting
swap
three
three way
time
twoway
Any one used one before? Picked up a job with a complete cockup on the wiring of the switching. Basically it boils down that I don't have enough cores to get the two way working...after a bit of googling I found this Vesternet APNT-92 - 2-Way Lighting using Fibaro Relays | Home Automation...
Can anyone help, I'm trying to replace a two way switch, but can't get both lights to work, i am a novice with electrics, however don't normally have problems replacing switches. The new switch is totally different to the old one and the colour of the wires is unusual.
Switch 1 - single switch...
hi guys
Anyone know of any good videos on YouTube for this?
I found some myself but I'm guessing a lot of you guys will know from experience the better guys to watch.
I know Pete shares a lot of this JW guy so I'm guessing he is good?
BarryJ90
Thread
best
circuits
electrical videos
explain
lighting
twoway
video
videos
Hi all,
I am new to this forum and I need help installing what I believe is a two way dimmer switch. I have a single light bulb on the stairs which has a switch upstairs as well as two lights in the sitting room which are downstairs. Both the lights on the stairs and the two lights in the...
Had another question about lighting this time as it seems to be what I struggle to get my head around the most and the book is very simplistic.
I came across a configuration today which I didn't think would work but it does and i just wondered what possible combinations there are? and what do...
DominicB
Thread
around
didn't
downstairs
lighting
twoway
upstairs
works
Hi
I have a job with a customer who wants his new kitchen which has been designed to have two way switching ofn12 sets of lights, some off them dimmed and some just switched.
My question is how would you do this? Client wants one bank of switches so grid set up best, a lot of cables to each...
I'm hoping to get a bit of expert advice on a problem I have with a friend's wiring. Initially I was asked to take a look at a three-bulb light fitting that was regularly blowing bulbs. I took the fitting down from the ceiling to check for loose wires and found that several came out from the...
Hi
I have recently had my kitchen ceiling lights replaced. There are 3x 18w led dimmable panel lights on a 2 way circuit.one of the switches is a 2 gang with one switch for the ceiling lights and the other for under cabinet/worktop lights.the other switch is a 1 gang for the ceiling lights.What...
Hi all,
I have an electrician helping me with some re wiring.
for two way switch I am proposing we do it as
1.5mm three core to ceiling
1.5mm three corr from ceiling to first switch
1mm 4 core to the second switch so that we have 1x ground , 2 for l1 and l2 and one for comm
His view was 1mm...
linux44
Thread
cable
electrician
light
single
switch
twoway
using
Hello, I wonder if anyone can help me with the following problem I have with a light switch.
I have a 3 story house and have a two way light switch on the 1st floor that controls the 1st floor landing and 2nd floor landing. The light on the 1st floor can also be controlled from the ground...
Hi, this is my first post on this forum.
I am a traning electrician on my third year of college (level 3 2365), should have had an apprenticeship by now, but hey, I'll be the last it seems...
anyway....
i recently moved house to a place which has the worst switch/sockets locations.
i have...
Hi All,
In preparation for a pending assessment, I have installed a new 2 way CU in my garage with all new wiring (my own property), and TT the earth. (House supply is TNC-S, PME).
I am testing the lighting circuit. (6a mcb / 2 switches / 2 way/ 1.5/1.0 cable . Have tested in all switch...
Hi,
I have been at a customers today doing various things, one was to change the switches.
The want a dimmer at the bottom of the stairs and a normal switch at the top.
I have never fitted these Schneider Ultimate Screwless faceplates before and now wish I hadn't started.
Anyway, I have this...
Hi, can anyone of you clever lot out there help me out.
I've got a ceiling rose with two twin and earth cables in old colours ( red, black ) and a single red switch wire to the lamp. The twin and earths are going to the loop live and neutral terminals, as seen in the photo attachment. I needed...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc