Hi all. I have noticed there are two schools of thought here when running a separate earth with a SWA to a large DB, where is the correct place to terminate the earth ? . We can go straight in to the internal copper earth bar as we have spare unnumbered holes for it , or we can lug it and go on...
Does any one have a link or know where I can find the diagram I’ve seen that lays out what rcd devices you can and cannot have up/downstream of each other?
e.g. you can’t install a type A downstream of a type AC etc
it was a good little diagram but I can’t seem to find it again, I think it was...
Is it acceptable to run mini trunking as shown in the pic? To my mind it would be safer (and slightly less ugly) to have a drop from each socket and then run it along the top of the skirting. I would be concerned about the trunking coming loose and being more likely to suffer mechanical...
I need one of these today, anyone know who has stock?
EMDH363
https://www.electrical2go.co.uk/63a-10-15ka-type-d-3p-mcb-emdh363.html?gclid=EAIaIQobChMI1Ku26ez6-gIVTbDtCh1tfQh1EAQYAyABEgJXTPD_BwE
Hi all,
I've recently had 2 customers enquire about installing a backup generator for their domestic premises.
After a lot of research, contacting generator manufacturers, and generally going around in circles, it's become apparent that TN-S, or "centre tap earth" generators are practically...
We bought a house and this conduit is outside my back door of my garage. It has 3 6g wires that have been cut and left in the conduit going into the ground. Any idea where the wires originate and go?
My solar panels and battey system were installed and MCS certified back in 2016. unfortunately the installers went bust not long after the install and I never got some of the paperwork. This didnt matter as at the time i didnt qualify for the FIT anyway and as long as it was registered with LABC...
My California dryer wall socket has 3 blades shown in picture. I measured across bottom 2 blades = 240VAC. I measured top L-blade with one of the bottom blade = 120V. Is the L-blade a neutral? If yes, why no Ground blade? If the L-blade is Ground instead, then why no Neutral blade?
I tried...
Hi, I’m just wondering has anyone on here any experience with a Mitsubishi Ecodan R32 model.
I’ve completed all the wiring expect for terminating two motorised valves. I cannot find a manual stating what terminals they go into. Any help is really appreciated.
Thanks
I have a job where the Ze is at 8.38 OHMS it was at 50.48 OHMS i have installed a new Earth rod but cant bring it down anymore has anyone got any advice on what I should do the mains is at least 300 meters away from the house my Zs is coming in at 8.72 OHMS for the sockets
Hi
So basically I went self employed at the end of January and I am currently subbying back to my old boss.
I'm not originally from where I live (Stamford, Lincolnshire) so dont have a big network of family or friends. My problem is how do I generate my own work. So far I've only picked up one...
Scenario...
2 x switched fused spurs located in a shower room. They are 610mm from side of shower, so outside zones. However, they could still get water on them from the shower so I don't feel they are suitable for the location. I can't find a reg for this though. is there one?
I realise...
This fuse link belongs to a Mercedes Benz. I have soldered the filament of the 40 amps fuse and I do not know if it works. The dealer does not have it and want to sell me the whole module. Are there ways I can go around it?
I am wiring 2 outlets in the ceiling to control 2 plug-in florescent shop lights in my garage. The 3 ways are at each side of the garage at the 2 entry doors. The way I have it wired right now, both lights come on at either switch but turn off if either is unplugged. I would like both outlets...
I'm setting up a pv system with a Trace Xantrex SW5548 inverter power wall. I'm going over the peripheral units (DC disconnect, AC disconnect and bypass switches and a T240 step up transformer for 220v usage. I bought a pre-owned system 10 years ago that I've had in storage and also found (2)...
I'm looking to fit two ovens at home, one conventional and a smaller combi oven/microwave. They are both rated at 16A. The current supply is a 10mm cable from the consumer unit on a 32A mcb. What's the best way to connect the two ovens to this supply? Do I need to incorporate a 16A mcb into...
I live in the UK but really admire some of the interior lighting in Spanish houses etc. In particular nice bright LED panels often found on kitchen ceilings. Not marvellous aesthetically, but they give a really useful, bright light. I can't seem to find anything resembling that online here...
I bought a single LED bulb today and was suppressed at the cost. As I'm intending to move over to LED which means changing all the bulbs in the house I'm looking for the best place to buy from and that means service not just price.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.