first day done of my AM2 exam. Just wanted to let people know what I done and if I will loose any marks.
So first of all risk assessment and safe isolation. I completed the risk assessment no problem at all and the safe isolation I completed fine as well asked for permission to isolate, prove...
Hi everyone,
Not going to lie I am crapping my self for my AM2 exam on Monday Morning at 8:00. So I just need a few questions answered:- tell me if I am right or wrong.
I will be using a megger tester by the way.
PEFC testing 3 phase ( 3 probe test) :-
Clamp croc clip on the neutral bar...
I have just been on the refreshers course for the Am2 exam that I am about to sit on Monday coming. When the tutor was going over PSCC and PEFC. I was confused, completley thrown.
So in my head I would do:-
I would carry out this test on the Incoming Tail side of the 3 phase board?
PSCC:-...
Hello all Sparkies,
Ive got a question how would you measure Zs on the installation at the origin? Even though the install is “dead”.
How do you test the motor circuit as in IR and Zs etc? Would you test the 3 phase IR from the supply to the contactor then do the same from the load side to the...
Hi everyone,
I am sitting my AM2 exam a week today and was wondering if the metal trunking, cable tray etc needs bonded back to the MET in the board?
Will you fail if its not bonded or will it be a minor?
Anyone got any ideas?
Thanks.
Hi all sparkies/apprentices,
A quick introduction I am currently a electrician apprentice with a domestic contractor just a small business. I have now complete my NVQ side of my qualification now sitting the dreaded AM2 Exam on the 12th Febuary until the 14th. However, I do have the refresher...
just about to book my AM2 as a final part to get myself approved.
What do I need to brush up on?
I’ve recently bought the regs book even though I know the 18th edition is due in June o_O and have a well thumbed on site guide somewhere, am I right in it being open book on the theory side...
Hi everyone.
I am currently doing my am2. Did they safe isolation today.
Not sure if I messed it up. For some reason I took the protective neutral cover off from the board then performed the 10 step isolation. I asked permission to isolate, labelled with warning signs and put key in pocket...
hi all,
Have my am2 next week... just brushing up on a few things.
Was looking for some advice on IR test on the whole consumer unit with a RCBO.
Is it ok to just remove the fly leads from RCBO or is it ok to disconnect and test live to neutral, live to earth, earth to neutral etc from the...
hi there
I'm new to this today but I was wondering if anyone could help,
I have my am2 on Monday and I can wire an ordinary 2 way intermediate circuit no problem but on my precourse the said that I need to take a neutral to every switch using t+e and was just confused to how I would do that...
Hi don’t do that much fault finding and could do with some help, AM2 7 faults to find using on a continuity tester so can only be one of four things, but not really sure what readings to expect?
Short circuit = tester should show a few ohms but may have some resistance in leads and bleep
Open...
Hi got AM2 in a few weeks, on the build there’s a 2 way and intermediate to wire up, I know how to wire one up but the way they want it doing is not the way I have ever done or the way I would do it, you need a neutral at every switch, from DB to first switch in T+E then 3 core to intermediate...
hi everyone.
I'm resitting my am2 in a couple of days for the install and I&T. I failed my install last time because my ring was incorrect. I was told sometimes the assessor will un-do a cable and you are supposed to check it...(is this true) and that may of failed me. I know this is a very...
hey I'm a new member to the site I've been doing electrical work for about 1 year and a half now and was an audio visual installer before hand. I completed my level 2 and 3 2330 city and guilds electrical course straight out of school but never found an apprenticeship in electrics bu ended up...
Hi all,
I am pretty new to this group so forgive me if this thread is already someplace else but i have just finished my second day of my AM2 online exam done, installation done, and part of my testing done ( just have to complete paperwork)
Theres a few minor things i know are wrong with my...
Hello everyone,
I have done my profiling for my NVQ with a provider, and paid already the fees for my AM2 and I'll do it in august, however I'm not really happy with this provider for my portfolio as the assesor is not helpful.
I would like to know if it's possible after I have done my AM2 to...
Hi everyone.
I am sitting my AM2 the end of this month (june) and have a few questions as my college is being very vague on things. some may seem very basic but any help would be appreciated.
first of, does anyone know weather the 2 way lighting circuit has to be wired in the two plate or...
Got my AM2 coming up on Monday, when conducting an R1 + R2 test on the s-plan heating system, would you connect the line and cpc in the DB, switch the FCU on then test between L&CPC at every point on the heating system and then note down your highest reading?
Secondly, how would you go about...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.