I had a couple of suggestions with regards to creating a dedicated Auto Electricians Forum category, so here it is.
Please post new threads by clicking the "Post New Thread" button once logged into the forum: Auto Electrician Forum - Electricians Forums
We will need a few threads created, so...
We're getting a lot of automatic replies to emails sent from the forum (thread subscription emails so ours are automated too). The irony. Emails automatically talking to each other eh?
Anyway, I fear a lot of the owners of the email addresses will actually be off holiday as I have seen quite a...
Hi has anyone fitted a small fountain pump with out shut off when the water in the reservoir gets too low. I have found larger pumps with float switches but they are all a bit large.
Thanks
just wondering if it might be an idea to have a forum on this. i just had to troll the net for a forum re. an electrical fault on missus's car. ended up on a renault forum, got the advice. basically, i had a good idea of what the fault was, but had no idea of where to access the faulty part. got...
Been asked to retrofit a current sensing immersion relay into a pv system. Manufactured by rudge renewables. Although it could be a great bit of kit it does look somewhat homemade. Anyone used them ?
Hello to everybody, I`m new here with pretty basic knowledge bout all that three phase electrical thing....
However I am here to ask you for a little help to source a part and/or eventually wire it.
So I`ve bought myself a big three phase compressor with Auto Star/Delta Starter. But there is a...
Ive noticed for a while now that some words are auto highlighted and if clicked to you to a link or advertisement... im wondering if this is forum related and do the linked pages sponsor the website or is this related to my explorer or such with a shadow program running in the background... i...
I am a trainee electrician, can any one tell me if i buy a second hand VC99+ 6999 auto range multimeter tester Amp C Tcompared FLUKE analog bar does this comply with the uk regs?
hsharp
Thread
amp
auto
comply
fluke
multimeter
range
tester
tests
can any1 explain how to wire a 3poistion switch (hand off auto) to control 2 lighting circuits which also is controlled by a time clock and has a photocell?
Hi Guys, Hope I'm in the right forum area.
So Have a 3 phase gennie set up which I've been involved in.
Customer has supplied the 125amp 3 phase gennie to run power at a workshop, and out buildings in the middle of a wood.
All went very well, and as a bonus a key switch was installed on the...
I have got a Seaward PrimeTest 350 and am just trying to get my head around the auto mode tests, and to also make sure the settings for these are correct.
A- Portable/Handheld/IT CLI
Visual Test > Earth Continuity (0.15) > Insulation (250v - 1.00)
B- Portable/Handheld/IT CLII
Visual Test >...
Ok, anyone got any ideas about the following "car" problem.
Last week, on our family holiday our trusty Ford S-Max refused to start, so I called the AA and they took it to a Ford dealer to "unlock" the immobiliser, test and they fitted a new battery. Just left it for about 62 hours and its very...
Ok Guys,
I Have a Wattson energy meter monitoring my PV and domestic energy usage.
I know alot of you guys dont like them but i seem to love it.
Only annoying thing is extracting the data and auto uploading it to PVoutput.org all the time.
I have 2 inverters, so don't want to fork out for 2...
Ok folks,
Here it goes, feedback will be greatly appreciated.
I have to two lighting circuits broke through two contactors, the control circuit is broke through a hand off auto switch at the minute, however I have to install a one way switch at a communal point/landords, etc. I have ran a twin...
Hi all using a megger multi and the auto null for the leads is playing up, you null them and then the reading goes up or even down, try again and then it mite go up even more, is it leads or meter folks, what you think all??:93:
Hi,
Need some advice regarding the installation of an automatic change-over switch to protect the supply to a small commercial server room with two cabinets.
The building has a three-phase TNS supply, and at present, the sub main supplying server room DB is a single phase 3 core SWA...
Jonny66
Thread
advice
auto
change
generator
phase
power
supply
switch
Hi all:waving:
Any help with this would be gratefully received :smiley2:
.
I have fitted some led lights into the front of my bumper and have wired them into the side lights as I didn't want them on all the time like DRL's but I want them to go off when I put the headlights on.
I guess I need...
Tawny Owl
Thread
auto
electric
electrical
led
lighting
lights
running
Hi guys
Happy new year to you all!
My van got done just after Christmas. About £2k worth of tools stolen.
Getting me a cheap car alarm at the mo to do me which wires to the internal light. Door opens, light goes on, alarm goes off...simples. The problem I have is I have 2 separate light...
Hello everyone!
I want to make an ATS for a house, with two power supplies, One from the power supply company and the other from a 5.6KVA Generator.
I am facing a problem with the DC section of the starting mechanism, I want to make it so that,
it should start the generator in a few second...
Dear all,
as suggested by the factory a Auto transformer tapping is 52% for our pump motor, which is 380V 3 phase.
As a result, I should demonstrate how's come the setting is 52 % for the captioned motor.
May I know for the calculation for it? what kind of information i should know before...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc