Hi I am converting a Sprinter van. I would like to use RCBOs. I want to run 3 seperat Circuits. 1 and 2 for sockets either side of the van and third to a Truma combi boiler. I will be connecting up a Victron Multiplus 2.
So please correct me if I have this wrong.
The 230v socket will be close...
Hello all,
I'm in the process of having my kitchen refurbished and I'm looking for advice on my current setup as I have been told that I will require a new consumer unit in order to connect the new induction hob and oven.
The oven requires 16a and the hob is 7.2kw
It looks like he intends put...
Hi can you power a second consumer unit in the garage from our main consumer unit. We have a big armed cable from the main consumer unit into the garage and can we connect this to a second consumer unit? The armed cable current runs our solor and comes from the fuse in the picture attached.
Hi all,
First time post to the forums, I hope you all go easy on me!
We are undertaking an electrical install as apart of a solar PV installation. We have a very small electric meter cupboard on the front external wall of the clients house and they're not keen on an external enclosure on show...
Is there a reg anywhere that states that you have to use the same make SPD inside a consumer unit. I know there are with MCB's as they obviously have to sit on the same bus bar but an SPD just slots in and has flexible cables wiring it up.
Hello all
I hope you are well.
I had a new Alarm Panel installed in January and all was working well until I got a new Consumer Unit installed Last Week which has RCBOs.
The previous Unit was just a Fuse Box.
The Alarm Panel is on its own Circuit connected via a Fused Spur.
The RCBO for the...
Hi, new member here! Thanks for any advice in advance. This week I got a new consumer unit installed. The electrician has just sent me through an EICR certificate. From what I had read I was under the impression that I needed an EIC form rather than an EICR. Is this the case? Is an EICR form...
Thought I'd give one of these a go.
Very easy to order and they build the board for you in the order you want. Next day delivery was free.
First impression is that it's very solid and the front comes on and off easily.
(So much space!)
When I fit it, if it doesn't look too rough I'll post some...
Generally, we would use the Wiska box. A couple of times apprentices have asked whether it would be OK to run a 6mm cable and join to the original ring mains in the Wiska. If the Wiska box is accessible for future R1+R2 testing, is there any reason this can't be done? My instinct is to say...
Hello.
I bought an empty consumer unit for installation in a shed project and now I have no idea how to install the neutral/earth terminals. The DIN rail won't fit the DIN terminals and there's only a space marked for the terminals.
Any help appreciated
Please help, just had a domestic EICR undertaken, a C2 issue: Consumer Unit does not meet minimum I.P rating, what does this mean and how do I check this out? how expensive to rectify? thanks!
Hi, My electrics keep tripping.. this black box in the picture seems to be the culprit. Slight touch of it and it trips. The electrician suggested removing this and connecting two main cables from main switch to the consumer unit with connectors. He said this black box is very old and not...
Done this loads of times before, but this situation is quite unique so bare with me.
I've been asked to cable up an out building at a country park which is about 30m from another out building which has mains supply already installed from a main building some distance away via a 10mm SWA buried...
Greetings all, just had a consumer unit upgraded and wanted your opinion before I have words with the electrician. Some stuff is obvious like the gland strip not fitted properly, you can’t just about make it ou, but others not sure off ie should the the meter tails have been fed separately from...
I recently had an electrician install a new consumer unit in my cellar. A second electrician, who is subcontracted by my bathroom fitter to carry out electrical work in the bathroom, has said that the cable entry to the fuseboard should be sealed with either fire resistant stuffing glands or...
I am in the habit of fitting 'Fusebox' consumer units. However, I notice that Danson are even cheaper.
Has anyone fitted them? Are they acceptable quality? Any problems with the RCBO's?
If they are 'Chint' like quality then I would rather avoid them. Chint are the only RCD's I have ever come...
Hi guys,
Just a quick one. I’m installing a garage board in, planning on a 6mm SWA supply coming from a 32a MCB. The DB I’m feeding from is a split load board.
My question is, what is the best way to move over the current MCBs to allow me to put in a MCB that’s not on any of the RCDs (as I...
He says 'it's fairly important to change the consumer unit as it wont pass the Inspection in its current state.'
He's coming round tomorrow to replace it, has he given me duff advice?
Cheers,
Matt
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.