grommets

Recent contents Top users
  1. OnlQQker

    Grommets and 10mm Hollow Threaded Tube

    Hello everyone, I'm currently making a table lamp out of driftwood found on the beach. Does anybody have any ideas about the cable passing through the 10mm threaded rod regarding grommets. I'm wondering whether I should use 3/8 BSP to 15mm plumbing connection to get me into a wider diameter...
  2. E

    Large grommets needed

    Hi does anyone know where I can source any larger round grommets ? I will be drilling a hole in 100 × 100 trunking so guess around 75mm hole. I've seen larger grommets before but they were a different material to rubber, they were like rubber but had fibre in them, a bit like bicycle tyre...
  3. W

    40mm x 37mm rectangular grommets

    Does anyone know where I can get grommets for a hole sized 40mm x 37mm. It's for the knockouts on a CGD consumer unit.
  4. D

    grommets and earth Sleeving are so over rated

    if you are going to put a 'how to' vid on youtube atleast buy a dang grommet and some G/y sleeve
    • Dustydazzler
    • Thread
    • and earth earth grommets rated sleeving
    • Replies: 25
    • Forum: UK Electrical Forum
  5. R

    Rubber Grommets Cable Entry - BS7671

    I am doing a non-compliance document for college. I have to find non-compliances whilst on site. I have seen an Intruder Alarm where the PVC Flexible cable is brought through bare metal, so no grommet is fitted. Can anyone tell me what part of BS7671 this would fall under and the definition, please?
  6. I

    Ip4x cant get 32mm grommets

    Would you guys recommend using a fire sealant to cover a hole on the the side and top of a consumer unit, I've cant get a 32mm grommets anywhere. Thanks
  7. E

    Missing grommets

    How would you code a missing grommet?
  8. Micktw68

    Oval Grommets for 15mm boxes

    Anyone have a supplier . Not used a shallow box for years and i cant find the grommets for love nor money
  9. xylophone

    Meter tail grommets

    Can the hive mind tell me where I can source the meter tail grommets that pack a 16mm insulated/sheathed tail up to 25mm? The Henley block knockouts are for 25mm cable and I want to maintain the IP rating for existing 16mm. I may use heatshrink as a solution but I know these things exist...
  10. Marti

    Fire Retardant Grommets

    An interesting grommets question...hold the front page. Wondered if anyone knew a supplier of the white fire retardant grommets normally used to seal a CCU at the point of cable entry? Wylex and BG make pre-packed kits, somewhat over priced for what they are but they sort-of do the job...
  11. J

    Hager Consumer Unit - Fire retardant grommets?

    When working on Wylex consumer units I always opted to use semi-blind fire retardant grommets. (British General Fire Retardant Semi-Blind Grommets 13 Pcs - https://www.screwfix.com/p/british-general-fire-retardant-semi-blind-grommets-13-pcs/9638p) These ensure that any internal fire is starved...
  12. S

    UK Are Grommets necessary

    Hi guys, I wanted to introduce myself to you all and was hoping to learn a few things from you guys. My name is Roland and I am a fully qualified gas safe engineer but looking in learning another trade. I like to learn more about electrics and was thinking to sign up on here. I was wondering...
  13. B

    Open grommets on cu top surface

    Hi, Got some additional circuits to install as part of an extension. CU has recently been changed by another contractor to an amd3 unit, but cables enter cu through a couple of knockouts on the top with standard open grommets. As it happens, the cables are so tightly packed in one you could...
  14. O

    Is there a shortage of grommets or knowledge and competence?

    So 3 days in a row I've seen new ish installs where the 3 different installers have failed to use grommets .. This is one I saw today: So apart from the fact theres no grommet and it doesn't comply with the IP ratings ..................... rant over ..........
    • Octopus
    • Thread
    • competence grommets knowledge
    • Replies: 41
    • Forum: UK Electrical Forum
  15. P

    M16 grommets

    Hey guys :) I need to terminate 6mm T&E, plus 6mm earth single, and 6mm SWA into an IP65 junction box. The junction box i am using is this one https://www.tlc-direct.co.uk/Products/LB9065.html The SWA will be glanced into the 20mm knockouts, and the 6MM T&E and 6mm earth single will be rear...
  16. G

    Grommets or conduit in metal back boxes?

    I've seen a few comments on failed installs because of lack of grommets - although apparently not a specific requirement as such. Is oval conduit plastered into chase and fed a little into the back box OK or does one HAVE to cut it just short of the the box and fit a grommet? Granted it's a...
  17. E

    Grommets

    Hi, I can't find anywhere the white plastic that you cut to length to make a grommet, for example in a new dis board to protect cables from metal hole, any suggestions? Thanks
    • edrobbo8
    • Thread
    • grommets
    • Replies: 9
    • Forum: Australia
  18. G

    Sleeving, grommets and other lazy faults

    Im getting really sick of going to jobs that have been done in the last few years where the electrician hasnt used sleeving, grommets ect. Im finding it very rare for electricians to bother with this stuff. Ive spent the last couple of months going round putting right and checking jobs done by...
    • grimysparks80
    • Thread
    • always fault faults grommets other sleeving sparks where
    • Replies: 58
    • Forum: Australia
  19. G

    Grommets

    Hi Chaps, Code for no grommets used ?????? A mate mentioned the other day it was a code 1 Your thoughts please G
  20. S

    Missing grommets

    Hi, What are people coding missing grommets on Galv backboxes. I was thinking a Code 2. This makes it a fail now as the Electrical Safety Council recommend that you put "unsatfactory" if there Codes 1 or 2. 80's the orignal wiring checks out with the other tests. Andy

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Top Bottom
Back