Hello guys
the niceic is coming to my home soon and they are going to check my work. When i phoned em up one if the advisors on the other side of the phone advised me that they are not concerned either you have submitted it to building control just that you can test and carry out everything ok...
Davey1988
Thread
certification
certsure
check
don't
niceic
other
result
scheme
sheets
test
visit
Attended a 1st floor flat in a council block today and found a supply head inside a mantel cabinet where the earth was connected around the outside of a conduit housing the main supply cables before going into the cutout. Also coming out of the bottom of the cutout was another 6mm2 earth which...
Hi
Have a new 1652B fluke multifunction meter
Nearly returned to fluke as ERR 5 kept coming up on 3 different locations when doing loop test, (this is due to apparently a noisy earth) as i explained to supplier everything unplugged why would this happen? the ANSWER is to get ERR 5...
Popped out to do a little job this morning ( 4 x t5 under unit strips replacement )
did the job, about an hours work being careful as it was an expensive kitchen, finished the job, cleaned up and got paid £ 50.00 tip for being tidy and professional ( his words not mine ) then just about to...
Evening all,
Just been having a nosey around the forums as usual. It would appear that the forum is going down the bog again, and is becoming like the well known DIY shed forum used to be.
It is a public forum, and everyone is entitled to their opinions and to say their piece. Some of the...
Hi,
I just done a job today and got some reading of 7ohms, on continuity of a light circuit (B6 CB) this is the highest I have yet seen
is this still ok? Or is this a problem?
Cheers
scintillasam
Thread
circuit
light
normal
point
result
start
switch
value
I'm so gutted I didn't take a picture today! Whilst visiting one of my guys on site (domestic) he took me to one of the back rooms of the house to show me a socket outlet that had been wired by one of the local NIC 5WWs a few years back. What I saw next was one of the worst things I have ever...
Just carried out a ze on a tt istallation and got a reading of 156 m ohms, carried the same test out a few months before and got 132 m ohms, the zs results were slightly higher as well! Could this be due to the changing conditions of the weather as to we're the earth rod is placed.
Thanks chris
oh dear god....
i recieved a cheque for 3k in my hand yesterday! after chasing them for nearly 6 months the director told me to deal direct with him and not the monkey in the office...!! (monkey subsequently been "laid off") and then asked me to price up some more work and do this and...
Q & A of the Day – What departure Code to use for this lighting test result? - Voltimum UK - Electrical Installation Products and Contracting
If you click on the link to the Votimum site the Q&A of the day I guy asks a question about testing a house light circuit for a PIR and NICEIC advise...
Hi all I passed my 2391 about 6months ago and thought I was flying, I know test procedures & how to carry out the tests like the back of my hand and I fully understand any results I get and how to rectify or diagnose any faults in a electrical system.....but then again I have only tested...
p11jor
Thread
2391
current
following
phases
question
result
supply
system
testing
Hello all, i have some dead testing to do, i just have a new megger Robin KMP3075DL and when using it in Insulation test mode (500v - 20Mohm) on 2.5 twin + earth as practice, i test between LINE and CPC and get the reading from the display (up arrow 1) so on my schedule of tests sheets what...
Hi
Getting used to Metrel tester and am getting used to testing and was just after advice on clarifying some points:
1 - FCU's with neon indicators on IR tests - whats the best way of disconnecting the neon lights on these if they cant be disconnected? Do I keep that particular FCU switched...
chrisgc
Thread
again
cooker
getting
insulation
insulation resistance
insulation resistance testing
resistance
result
sheets
testing
Check this system out
Trina 235w x 17
Solar edge SE4000 and 17 x Power optimizers
south facing
Aberdeen scotland NOTE READING FOR 20th MAY ..... 29.32 KWH in one day WOW WEEEEEEEEEEEEE has any body witness higher than that ? 424 kwh already in MAY ................ the owner...
Hi
New to trade and 1st post – any help/advice appreciated
Testing DIY installation approx. 10 years old. Final circuit for sockets – a radial (not ring) wired in 2.5mm T&E protected by 20A mcb to BSEN 60898. Not logically wired, several JBs in loft and a number of spurs so not easy to...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc