Morning.
The LED light above my bath doesn't work. I yanked all the stuff out the ceiling and found this.
So far, so good. But hark!
I have come to the conclusion that something is wrong with the transformer. Worst case: it may never transform again.
If I just buy another one with the...
Scenario: Visibly burnt out, entirely blackened, ballast in a fluorescent fitting. Would this be noteworthy during an EICR and if so, how would it be coded? My thinking is that its an obvious fire risk.
Still an apprentice with millions to learn, any input would be appreciated.
Had a callout for a landlord as the bathroom fan stopped working.
Didnt take too long to work out why...
Never seen a fan quite as bad as this before!!
Wonder what caused this, possibly got jammed and overheated?
Have a fault where the ecomony 7 (or whatever it's called) overnight water heater element keeps causing heat damage to the fuse in the local fused switch.
The element seems to be 15A rated so the first time I was called out I told the landlord it was too high for the 13A fused switch and needed...
Just arrived at a job, 45amp shower isolator completely burnt out.
Checked cable and it's 4mm tne in trunking to 8.5kw triton riba shower on a 32amp mcb. Cable run is 5meters.
This was a new circuit installed only a few months ago. I expect loose connection on isolator causing burnt...
Did an EICR opened the CU and found this burnt charred Neutral running downstream of the (main switch). What should I be looking for (other than a replacement tail)?
There were two or three C2 observations that may well have caused an overload - eg 5kW of water immersion wired into the ring...
Hi,
i recent bought a 2 poster screw type car ramp. Changed the motor for a 2.2kw motor. Wired it up and tested it with nothing on it and it went up and down no bother.
Put my 1 tonne Clio on it and it lifted about 1ft off the ground and then ground to a hault. It went back down no bother...
Morning all,
been asked to to look at an old fusebox (Wylex) where the main switch has been burnt away due to a loose incoming live tail connection.
obviously no spares are available, so it's deffo gonna be a new unit. Ordinarily I know this would mean a full eicr before changing the unit, but...
maffa ent
Thread
before
burnt
carry
change
main
main switch
out
repair
switch
tests
A plumber has installed a 8.3kw heating boiler pulling 35a which is being fed from a 6mm . it has burnt two 45a cooker switches already. Why. Rewiring to 10mm will be hard as tenants just moved in. Owner going mad ! Cable is running above ceiling near downlighters and poss insulation. Also...
It's a TT so I reckon I'll sleep better at night knowing that if there was a fault to earth upstream of the RCDs the customer wouldn't get a brutal/possibly fatal belt. Just going to put it in the departures section of cert and discuss it at my annual inspection with my assessor.
I know I have...
Lazlo
Thread
burnt
domestic
fault
fitting
metal
out
plastic
tails
watch
Evening all, been called out to a campsite to a hook up that looks like a dalek. This hook up is supplied by 32a on 6mm 3 core swa and supply's a 40amp rcd and 2 c6 mcbs. The mcbs then feed 2 of the blue industrial 3 pin outlets. The rcd was burnt out through the side and knackered. I am going...
Hi All,
Newbie poster here, so treat me gently. I have been a domestic spark for about 5 years fully qualified and registered etc....
I tend to read posts on here rather than post questions myself as I tend to find from the great wealth of knowledge and experience on here I can generally find...
I always buy a poppy its my way of saying thanks to people who give there lives (or part of) so we can be free.then heard of this incident where a 15 year old cadet was attacked with a flaming aerosol.
see http://www.bbc.co.uk/news/uk-england-manchester-29870960
Hope they catch him:bobby:
Is there any guidance / reg regarding how far insulation should be stripped back once it has been overheated due to an accessory / termination issue? Example, shower / cooker switch faulty (so heat source local therefore whole length does not need replacing) 1" burnt then further 2"...
Just noticed a fault with my cooker as in the cooker will not switch off from the mains switch on the wall. Isolated the cooker at the CU and took the switch off the wall and investigated what was going on.
When opened I noticed that there was a live wire sitting loose in the socket and it has...
So was visiting a friend and they happened to have a problem with their cooker....it stopped working mid cooking a dinner!
Ok so BEKO electric oven with Gas hob.
Rating of electric oven is 2.5KW
Was hard wired into a FCU with a 13Amp fuse.
Wired in what I assumed to be 1.5mm2 white flex...
Basically, circuit board was gold before in area I wanted to solder, now it's black, if i place wire there and solder correctly will it work?
Look at pics, thanks.
Area is highlighted, before colour is on left, after on right.
Can't type for long/in depth - gotta sleep but help please?
Been looking at a CU where the main switch has burnt out, or rather the N connection on the bottom has. The busbar is fine. Upon inspection, the plastic back of the CU has the residue of burning but no actual damage (that I can see). I don't like leaving this but the customer already has a...
Hi all, I have a storage heater (Creda ER500) the mains plug works fine but the off-peak plug has a burn mark on the back.. When I opened up the plug the live wire was badly burnt and the wall socket was cracked. I was surprised to find the 13A fuse had not blown. What could of caused this and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.