final

Recent contents Top users
  1. Marcus Vaughan

    Power to an Outside Office - Spur from Ring Final?

    Hi All, Just looking for some reassurance on a job I've looked at today. My status is that I am trying to stay within the realms of 'Minor Works' until I get a bit of experience under my belt. Conscientious decision - but everywhere I go it seems that notifiable work is needed as well...
  2. A

    18th edition final changes released by IET

    Changes in the 18th Edition IET Wiring Regulations - IET Electrical -...
  3. L

    Final Circuit Protection

    Hi Everybody Why fuse is no longer use in Final Circuit Protection. Instead, Circuit breakers are used. So far, I know that CB is more sensitive than fuse. Can someone depicts any reason and their respective curves. Thanks
  4. Marcus Vaughan

    High(ish Zs and extending ring final question.

    Hi all. Love the forum by the way. I do have a question though... I have just visited a house (on a Sunday!). Customer is asking for additional sockets onto 32amp ring final. Circuit is 30mA RCD protected. Wiring is 2.5mm/1.5mm tinned copper. Thought I’d better do a live Zs test. Zs = 1.29...
  5. B

    Fault finding on ring final circuit

    Fault finding on ring final, is this the readings you would expect to achieve and are these the correct way to find them thanks
  6. 7

    Ring final testing question

    Testing my extensions wiring today and noticed cpc fails continuity. Howevery I have continuity from outward leg to main earthing bar in CU Any ideas how ?
  7. T

    R1 R2 socket test on Ring Final Circuit with megger leads

    So with megger leads they are not too happy in a kewtech socket tester so what do you do when you want to do this use kewtech leads on the megger? The megger leads clearly do not fit into the kewtech. Just use the plug lead?
    • The Ghost
    • Thread
    • circuit final leads megger ring ring final socket test
    • Replies: 16
    • Forum: UK Electrical Forum
  8. A

    R1+r2 reading and r1,r2 and rn on ring final

    Hi there Been stuck on this for a while. What is the maximum r1+r2 reading possible on a lighting circuit in a domestic property. With a type b 6amp breaker. Also if you guys could tell me about r1+r2 and rn Maximum readings for ring final. Thanks
  9. D

    SY cable for distribution circuits and final circuits

    Hi all, Just a question relating to SY cable and the use of SY cable. My boss his carrying out a EICR for a industrial premise and coming across a lot of SY cable. These cables are used for final circuits and distribution circuits. I know that BS7671 list SY cable as non - standard cables and...
  10. Marcus Vaughan

    High r1, rn, r2 etc on ring final.

    Hi All. I had a job which was going to be a 'quicky' fault finding and repairing a couple of sockets, then it came to the testing..... The consumer unit gave me no cause for alarm but was all labelled up wrong, so it turned out there were far more sockets and square meterage on this ring final...
  11. Amateur

    Ring Final Cable Routing Through Bungalow Loft

    Hi all. I know there is a DIY forum but im really after your expert knowledge rather than fellow DIY'ers/amateurs. With regards to replacing a section of a bedroom ring final circuit in a bungalow loft what is your preferred method of cable routing taking into account insulation and not being...
  12. J

    EICR code Split cpc on ring final circuit

    lost continuity on cpc of ring circuit, live and neutral fine all test fine. C2,C3,FI ?
  13. M

    Faulty MCB. Problem isolating ring final circuit at CU with MCB

    I am planning to move a socket outlet. The CU is largely unlabelled so don't know which 32 MCB to switch off. There are 2 x 32a MCB. All other mcbs are for lights (6a) and a dedicated immersion (16a). To isolate the circuit, I tried switching off the first of the two 32a mcb which isolated some...
    • maxeon
    • Thread
    • circuit faulty final isolating mcb problem ring ring final
    • Replies: 50
    • Forum: UK Electrical Forum
  14. C

    Scrap the Ring final circuit

    After coming across countless faults in domestic premises regarding ring final circuits, I reckon they should scrap em... Gets frustrating when you go to check continuity and there is nothing between each leg. Or you get a call to check a burning smell from the C.U and once again a broken ring...
  15. R

    Low IR ring final circuit

    Testing a ring final circuit today. R1+R2 is fine, same as end to end r1 rn and r2. However IR test is coming back 1.87M ohm. I split the circuit and located a section (one side of the ring is clear >999). The customer doesn't want any walls or ceiling touched. As this is greater than 1M ohm...
  16. M

    Odd Fault on Ring Final

    Hi, Went to look at a job today where the customer reported the RCD intermittently tripping. I did an RCD Trip test and it failed to trip on x1, x5 or ramp test, the mechanical button tripped it. After a bit of further testing I discovered that the Kitchen RFC had an IR reading of 0.00 meg...
    • markadams
    • Thread
    • fault final ring ring final
    • Replies: 13
    • Forum: UK Electrical Forum
  17. H

    Ring final install method query

    Hope someone can help. When finding the cabling current capacity for a ring (wired in 2.5), would you use the data for 4mm in either/or table D5 of BYB or table 7.1 (11) in the OSG ? As the ring circuit is in effect 5mm ! Looking at the OSG ref methods; a 2.5 with ref method 101 says 17A...
    • haptism
    • Thread
    • final install method query ring ring final
    • Replies: 16
    • Forum: UK Electrical Forum
  18. Soulsurfer

    Ring final & Radial circuits off one mcb ?

    Another straight forward job today has turned out to be a right mess once again so I thought I'd get some thoughts on the following before I start ! So an old MK LN59 board, feed to garage sockets on a single 2.5mm t&e from a 15A mcb and also spurred to feed a boiler on S plan, Next ring final...
  19. C

    Starting point for discontinuous earth fault on final ring.

    Hi all, I have a 32A Final Ring Circuit that I have swapped a single socket to a FSU for an outside light. I'm now testing it and finding it has a discontinuous earth - I'm also kicking myself for not checking from the off but we learn. Anyway from the attached image you should be able to see...
    • CDB
    • Thread
    • earth fault final point ring starting
    • Replies: 18
    • Forum: UK Electrical Forum
  20. S

    Ring Final Circuit wired in 4 core SWA

    Hi Gents, Have an existing circuit at a warehouse where a single 4mm 4core SWA has been used as a Ring Final Circuit. Two cores are in connectors in the back of the socket outlets thus creating a ring. The SWA is therefore the sole means of earthing. There are No banjo's at the sockets and the...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Top Bottom
Back