manufacturer

Recent contents Top users
  1. N

    Help Identify Electric Storage Heater Manufacturer to see if Contains Asbestos

    Hello, I recently bought a 1960s-built house. It had an electric storage heater in it that I wanted to remove. A notice on the heater said to remove the bricks before undoing the wall mounts so I went about taking the bricks out. This was fine for the layer in front of the heating elements but...
    • Novice12
    • Thread
    • asbestos electric electrical heater identify manufacturer storage storage heater
    • Replies: 13
    • Forum: UK Electrical Forum
  2. J

    240v Fan in zone 1

    Hi folks new to this but have a question . What are the circumstances that have to be met to fit a 240v fan in zone 1 . I have read that it's acceptable if the fan is ipx4 rated and is on a rcd. I've read that if the manufacturer states the fan is suitable for zone 1 and rcd protected then it is...
  3. R

    LED Flood Light Flicker Like Strobe Fault. Suggestions For Manufacturer Replacement.

    Hi, I have recently been having a fault with my LED flood light in my garden. It works OK for about 3 minutes and then flickers like a strobe. If you turn it off for a period, then turn it back on again it works for 3 minutes again and then again flickers like a strobe. I have had these lights...
    • RobMS88
    • Thread
    • fault flicker flood led light manufacturer replacement suggestions
    • Replies: 6
    • Forum: DIY Electrical Advice
  4. SolarCity

    Inverter replacements by manufacturer - invalidate warranty?

    I've noticed some manufacturers are replacing inverters themselves rather than sending the inverter to the installer. I wonder whether this could void the warranty for some firms?
  5. M

    MCS 012 fire rating in roof systems

    Hi All reading the guide it mentions performance of different panels & how they react, Maybe with all the guidelines & standards we have to adopt they should have had more stringent standards on the panels in the first place & then they would not need the requirement. Evidence has emerged...
  6. E

    Rcbo On A Busbar Protected By Rcb

    Hi just looking for your opinions on putting an RCBO on as busbar protected by an RCD, the reason i ask is the manufacturer doesnt make a 45A MCB but does make a 45A RCBO. or leave the circuit on a 40A MCB even though the manufacturer of the oven asks for a 45A supply?
  7. C

    Replacement panels for a defunct manufacturer

    Afternoon all We have a couple of damaged Day4Energy 240w modules to replace and so far as I can tell this company no-longer exists. Well not in the same form as it did a few years ago anyway. A new company has taken up the technology but are not producing these panels. They have suggested...
  8. O

    Name the manufacturer

    Got sent this photo today: Can anyone name the manufacturer? They date back to about 1990 Thanks
  9. O

    name the manufacturer?

    Guys and girls Can anyone name the manufacturer of this: Its about 15 years old if that helps thanks
  10. S

    smoke alarms

    HI Everybody ! what is the correct minimal distance from doorway and wall for smoke alarm? is it 300mm from wall, door and any light fitting ? Just working on loft conversion , no fire doors so fire alarm in every bedroom needed! just wonder about positioning. thanks
  11. J

    Voltage drop for fp200

    Hi, Am running a radial power circuit in 4mm fp200 with a 20A rcbo but am a bit worried about the voltage drop. I have a 70M run clipped direct and by my calculations I will need to go to 6mm. I am using table 4d2 but don't know if there is a table for fp200.
  12. T

    One third of SMA staff to lose jobs

    Detail in this article: One-third of SMA staff to lose their jobs: pv-magazine Although most of the losses will be in Germany, does this mean reduced levels of support in the UK?
    • The Solar King
    • Thread
    • electrical work jobs magazine manufacturer staff their third
    • Replies: 1
    • Forum: Green Lounge (Access Only)
  13. S

    Does a sunbed require RCD?

    Hi I've been asked to install a power supply for a sun bed in a salon: Sunbed is 60 x 225w lamps = 13.5K Divide 230v = 59amps Table 4D2A: 10mm T&E 63amp capacity clipped direct. I'm installing a dedicated CU with a 63a MCB and isolator fed via a henley block on the meter tails for the sunbed to...
  14. J

    LED ceiling tiles startup current

    I have been asked to quote a shop fit out that will have 52x 45w LED ceiling tiles overall. they would like 12 switched at a time if possible, but on a previous job I only had 6 on one switch and had to use a 10A C-type MCB just to sto pthem tripping out on startup. I was thinking of wiring...
    • joelypops
    • Thread
    • ceiling contactors current going inrush led manufacturer switch tiles
    • Replies: 8
    • Forum: UK Electrical Forum
  15. A

    Cordless chuck witch manufacturer is best?

    I have a hitachi hss chuck even though I can't praise the drill enough I've had issues with the chuck and I replaced it with a supposedly heavy duty ( wasn't cheap !) but turnd out to be crap sticking closed all time and bit constantly dropping out , just wondering for the opinion of others...
  16. B

    What Manufacturer is ths HELP

    I have come across an emergency stop button that i have to match and i cant find aything so far, it looks like most other lockable emergency stop push buttons and the only marking on it is the logo TC in white writing in a small black rectangle. If anybody knows who has made or branded this...
  17. S

    Panel Corrosion from Salt Water?

    Looking for some advice/opinion on the issue I am having with my solar installation. I have 22 x 180w panels (I wont name the manufacturer) connected to a PVI-3.6-TL. The system was installed in April 2011 and was working fine up until roughly Nov 2012. The inverter shows the error message...
  18. T

    LED Driver

    Hi All I have never posted before but i need some advice, I need to source a LED Driver my wholesaler says that it cant find it the driver in question is AC Adaptor 24v dc 2 amp the above is what it says on the driver it self the driver is used on a led round feature in a retail unit Can...
  19. P

    Testers failed calibration but perplexed now :-(

    My MFT failed calibration on some insulations resistance measurements but i am a little confused. I used a different more local calibrater as i needed the least downtime but his certificate is very different from the manufacturers one that was done before (now i have had time to compare side by...
  20. S

    rail manufacturer

    Hi, Can anyone advise me the make of mounting kit used here please and also who supplies this? Thank you

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Top Bottom
Back