stuff

Recent contents Top users
  1. T

    1st CCTV job.

    I have been asked by a chip shop owner to install a CCTV camera above the till in the shop. However. There is no office or anywhere suitable to run the dvr and monitor to. No wifi to use an ip cam. All there is, is a suspended ceiling full of lights and a void above. Any ideas would be greatly...
    • TobyTheSpark
    • Thread
    • cctv electrical work fitting job stuff
    • Replies: 13
    • Forum: Australia
  2. A

    Anyone use CED stuff?

    As the title says - CED 12 way board loaded from toolstation at for £54 incl free delivery! Never used CED stuff before, lot cheaper than the hagar stuff i'm using at the moment.To good to be true?
  3. D

    Rcbo

    32amp(6,10,16,20,40 amp) RCBO Hager/Wylex Replacement on eBay (end time 17-Jul-10 17:15:54 BST) i DARE any body to build an install from them RCBO's!! :D
    • DurhamSparky
    • Thread
    • again boxes cheap hager rcbo stuff
    • Replies: 15
    • Forum: Australia
  4. A

    New to this self employed stuff....

    I’m a self employed Electrician, with experience in Industrial/Commercial mainly, looking for some information on the requirements for me to start doing my own work. I did a JTL apprenticeship with a local firm resulting in an NVQ level 3. I was made redundant last year and became self...
    • ajs
    • Thread
    • employed new self self employed stuff
    • Replies: 2
    • Forum: Business Related
  5. B

    sum usefull stuff to study 2391 pt 3

    Q36 state two reasons for confirming the value of Ze for a new installation A36 (i) to verify the existence of a supply to earth (ii) to verify that the Ze is not greater than the value used in any of the design calculations, this value can be added to R1+R2 values to give a Zs value for...
  6. B

    sum usefull stuff 2391 pt2

    Q21 list three things to check when inspecting overcurrent devices A21 (i) correct BS and type (ii) Correct current setting (iii) adequate breaking capacity Q22 list four instances where a TN-C-S System is not allowed A22 (i) construction sites (ii) supplies to caravans (iii) supplies to...
  7. D

    to NAPIT or not to NAPIT

    Is anyone here with NAPIT. I so what was their interview process like?
    • dma.electrical
    • Thread
    • experience money napit stuff their
    • Replies: 8
    • Forum: Business Related
  8. W

    data feeds and stuff

    I've been asked to run cables for a small network while the property is undergoing refurbishment. Would cat5 cable suffice for both telephones and broadband extensions?
    • wattsup
    • Thread
    • data feeds stuff
    • Replies: 4
    • Forum: Australia
  9. D

    van stuff

    right starting to kit my van out and was wondering what you guys use for the pipe carrier? did you buy a preformed one for £--- quid or did you make one?? i can get my hand on some nice ducting in grey and chop it down to size or would you just recomend i buy one??
    • DurhamSparky
    • Thread
    • electricians vans stuff van vehicle
    • Replies: 22
    • Forum: Australia
  10. E

    Ladders & Other Stuff

    Sorry for all the posts regarding tools. I have just decided to buy all the things I have wanted over the last few months and upgrade some older stuff. Really want to upgrade my old ladders as they are about as straight as.......... well I better not say. Was looking at Aluminium or...
  11. gaffer

    black enamel conduit

    Just out of interest really,do any of you guys ever use black enamel steel conduit any more?.Did loads in my apprenticeship in the mid eighties,but that was probably the last time I used it.
  12. G

    Computer stuff.

    Afternoon peeps. Would anyone be good enough to share with me the way of converting a word document to a PDF document. Ta. Sorry, should have added without paying.:D
    • Guest123
    • Thread
    • computer stuff
    • Replies: 10
    • Forum: Electrician Talk
  13. A

    Pat Testing Stuff : 2009/10

    Building Regulations ;) do state that structures built of combustible material ( i.e. a wooden shed ) must be at least 2 metres from the main house...
  14. E

    Is Bosch 10.8v stuff any good?

    Today I managed to drop my nearly new Bosch 14.4v-LI driver down a cavity and after much messing around trying to rescue it have decided it has gone for good. Looking for a suitable alternative I used to have some of their 10.8v stuff but never used it too much so sold it last year. I have...
  15. S

    What stuff is recommended

    Hi All, I'm just starting out, and I was wondering what you guys tend to recommend with regards to brands of consumer units, accessories, etc. Cheers Steve
  16. L

    av stuff

    does anybody on here do any av systems im looking to learn a bit more about them like wiring diagrams and what cable you need where etc iv been on avforum lots of nice pictures of finished stuff but no diagrams which would help me understand a bit better any help would be gratefull
    • lockhes
    • Thread
    • stuff
    • Replies: 10
    • Forum: Australia
  17. G

    mini trunking

    Ok, here goes for my first really basic question. I've planning a couple of jobs for my Part P assessemnt with Elecsa. And one of the jobs will involve running some T&E through plastic mini-trunking. I haven't installed mini-trunking before and I have been looking into the options and as far as...
    • Gerry24
    • Thread
    • adhesive option stuff though trunking
    • Replies: 8
    • Forum: Australia
  18. sparkdog

    16th edition stuff

    Is there any point in keeping all the 16th edition references like Regs,OSG,GN3 as I have had to replace them all with the 17th edition ones?Not sure if they are likely to be useful for something or if I should bin 'em.Regards,Sparkdog.
  19. A

    2356 Underpinning Knowledge???

    Anyone know about this multi choice and short written answer exam? I have been asked to take it but rather than bone up on stuff I won't need I was wondering if anyone had past papers or model questions? Not fussed about answers but wouldn't turn my nose up either!
  20. scotsparky

    does swearing at stuff help??

    We have all done it a hard to reach bolt,rusted scews and we start to swear but does it help?? or is it the position of the tounge sticking out the mouth at an angle the best method??:D

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Workwear Shropshire
Top Bottom
Back