The final registration for the City & Guilds NVQ 2356-99 (Mature Candidate Assessment) will be on 31/12/2020. This means that we cannot enrol anyone on the NVQ 2356-99 after 31/12/2020. Anyone enrolling on the City & Guilds NVQ 2356-99 before 31/12/2020 will have three years to complete the NVQ...
I was talking to an apprentice yesterday who was moaning about the length of wait to do his AM2. There is a new centre in Maidstone South that has plenty of availability and does the AM2revision day.
How would I pinpoint a fault on a ring circuit with very little resistances, and without any visual clues, only by measuring.
Say I have a break in neutral between db and first socket. How would I go about fault finding it?
1. I will use low resistance ohmmeter.
2. I will find that rn is not a...
How come the sequence of tests in guidance note 3 is that the Zs test comes before the PFC test?
Isn't it normal to do PFC test before the Zs test? Because then you can do your PFC test, put the board cover on and energize the board without coming back to do the PFC test.
Hi, could anyone tell me how to prove in a book that the highest x5 of an RCD test is sufficient please? It’s a question on my am2 testing. Thanks
I’m also struggling on how to check that my measure PFC at DB will trip the breakers in time. This question was a tick box on the exam so if anyone...
Hi, was wondering if anyone could help me please.
just re sat my am2 testing exam but failed because i didn't verify my results correctly to the book and table when they ask on the question sheet through out the exam.
i am hoping someone who has done it recently could point me in the right...
I've just come across a post saying that the new AM2E will be starting from October.
Apparently there's already an AM2S as well the normal AM2.
Does anyone know what is different between the 3 assessments?
Surely it should just be the same practical assessment for all electricians looking to...
Hello
1. When taking R1+R2 readings on the AM2 composite installation are we expected to take the reading at the supply side of the FCU (S-plan & CO detector circuits) or at the farthest point of the circuit? I know with EICRs we only test to the FCU.
2. With the fault finding they list 4 fault...
Hey all,
I’ve completed level 2 and 3, 18th, 2391-52.
I am looking for a goodplace to complete my AM2 course In the north west area preferably.
Also want to complete the end of my NVQ after getting my AM2...does anyone know where I could do this?
alsohas anyone information on tips/tricks for...
I recently finished my AM2 and unfortunately failed. The only thing I failed on was the earth fault loop impedance. I’m booking a resit but don’t want to fail it again, the procedure I carried out was.
Isolate and lock of the main switch.
Remove the main earth from terminal.
Set tester to L-PE...
Hi guys can someone tell me what the triangle symbols mean on the earth bar as i terminated my water and gas 10mm bonding conductors into them and failed my am2 because of it ?
Thanks
Hi, found out today that my AM2 has been cancelled which I was due to start this coming Monday due to coronavirus and the college think it will be a couple of months before I can take the test.
Is there a chance where they can say the test is void due to this as the backlog will be huge plus I...
Hi I want too do my AM2 In the future. I want too know the breaker selection for the circuits in the AM2, an acceptable answer (for me.) will be from a recent am2 Passee (successful candidates only.).
The circuits are as Follows:-
D.O.L Starter, with motor.
Carbon Monoxide Detector
Ring Final...
I achieved my 236-1 and 2 between the years 1992 and 1997. I have just received my AM2 certificate. I have been working as an electrician for over twenty years. Can I now apply for a jib card with what I’ve got or will I need to do an nvq3.
thanks in advance.
Hello
I am taking my AM2 in 8 weeks and have some questions that I was hoping you guys could answer for me?
1. Does the pre-installed metal containment require earthing?
2. When wiring the RFC do you follow the specification (with a long leg from the final socket-outlet back to the board or can...
Hi everyone just to let everyone know that I did my AM2 last week and I only failed on the fault finding part. I was very confident before going into the fault finding test but I lost my way and the pressure got to me. I'm so chuffed that I pass everything else.
Just to explain what the test...
Hi All
I'm looking for some advice regarding the AM2. I'm hoping to carry out the NVQ 2356 in electrical maintenance as I have been working in the industry for around 10 years and currently hold L2 & L3 2365 although I have limited experience in install as I work in maintenance at the airport...
Hi everyone,
I've been reading alot of post regarding AM2 on here and they're all really helpful. I've got a question on the electrical installation cert. With regards to nature of supply parameters you test the Ze with the earthing conductor out then you put that earth back in. Then you do...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.