Hi,
First time posting on here so apologies if I'm missing any basic information, but hopefully someone can help me as an amateur DIY-er and definitely not electrically knowledgeable. I suspect the best approach would be to get in a professional to help, which I'll likely do but interested in...
I've just had a EICR completed and it has C2's for cables concealed, in walls at a depth less than 50mm, containing metal parts and no RCD(s) provided for additional protection.
All the circuits are for night storage heaters and come from a seperate DB on night tariff and where installed in...
Firstly thanks for the chance to find advice I need. I'm a qualified gas/heating engineer with over 20years exp. Icometed about 3 years of night school whilst working as an electricians mate over 20 years ago ( before heating) I know how to bend tube,tray,and have experience in house wiring,3...
Hi,
We have recently had some electrical work completed in the house to add a new circuit for air conditioning.
We are now experiencing intermittent RCD trips, at all hours of the day and night, in the section of the consumer unit that the new A/C MCB was installed into.
No MCB's trip - just...
Hi,
I have a double electric socket, standard 13amp. My son broke a plug in one of the sockets so I decided to change it.
The new one I purchased had 2 connections for the earth wire whereas my old one only had 1. I read that it's ok to only use one of the connections so I did. Once...
Hi guys, I'm having an issue with a tire machine I was called too.
The machine won't reverse. I replaced the original switch with a new one. I can get it going forward but no reverse but I can wire it to make it drive forward on both switches.
Is this me being stupid and no connecting back...
Hi all,
Over the weekend I swapped out a light fixture in a bedroom that had a Loop-in ceiling rose to a modern pendant light that had a choc block style terminal only.
I used Wago connectors and Wago box to wire everything up and put it in the ceiling. Before doing any work I flipped all...
Hi all could someone advise me on if it is possible to change this light switch to a new one that I have already bought . The one in the picture is for 2 way switching on an upper landing level with the other switch on the lower landing level - it operates the lights on both landings only, but...
Hi, so I'm looking at changing my thermostat from a honeywell manual to a honeywell DT90E digital thermostat and I was wondering if you could help me with where the wires should go please. First picture is the wiring of my current thermostat and the second picture is the instructions for the new...
I am changing an old MEM 2 way light switch for A MK Logic one, have have a wiring question. The MEM switch has 3 wires into it, red, blue and yellow, with Red going to Common at the top of the switch, the blue wire goes to the bottom left, and yellow bottom right.
on the MK logic switch, there...
Trying to change out an old 1980 dual wall ceiling fan light switch , but the old wiring doesn't seem to have the same type of wiring as the new switch we bought. Inside of the old switch it looks as though they split and then soldered the black wiring underneath the casing so they could...
Hi All,
I would be extremely grateful for advice/comments on the following :
My old built-under hard-wired oven died and due to space constraints I have only found 1 option to replace it :
https://www.myappliances.co.uk/Innocenti-ART28772-Omega-Lux-60cm-73-Litre-Fan-Electric-Oven
[According to...
Greetings
I have this fancy ceiling tube light fitting and I cannot figure out how to replace the tubes.
It has two ends which somewhat come away but not enough to remove the tubes. There is wiring both sides.
I'm not sure how much more pressure I can apply before something breaks. There are...
Removing a 20 yo smoke alarm, wired in. Two cables coming through a rafter 'hole', fastened into the alarm. Chocolate block (whatever they are called these days) used to connect the alarm to the incoming mains.
Question: Entire chocolate block (5 connections) won't go through the rafter hole...
I rent out a flat in a small west London block built in 1990s. 2 storage heaters installed around 2005 now have stuck or broken switches so I'm looking for advice about replacement. One has both night and a daytime part, but the other seems to be only wired to the night meter with no other power...
Kevmul
Thread
advice
changing
heaters
night
please
replacing
storage
So I’ve took the casings of to look at the wires for one light. There are 2 of each brown blue and earth. The two earths go to the part that holds the bulb, the two blue meet in a connector with a wire coming out of that connector to the bulb component. Now one of the brown wires goes to the...
Hello,
I've recently bought four light fittings (to replace the existing simple ceiling light pendants) that look like the following to wire up:
I've already changed two of the four pendants since they are just a single wire coming in (from the other hallway/landing light) so they were...
Hi All,
I need to change a DB in a block of flats in central London (W2 postcode), where EDF can't give a date for at least 6 weeks to come and isolate the supply, but at the same time won't / can't give out a date after this, which makes no sense to me!
This is both options of just popping...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.