Hi,
I am an amateur with little knowledge of electrics, so please bear with me.
I recently bought a petrol generator Pacini 6.5KVA Petrol 13HP Generator, Electric start - https://ige.ie/pacini-6-5kva-petrol-13hp-generator-electric-start
The purpose of the generator is to power basic...
Good day. My daughter bought an older house and wanted to change a 240 volts baseboard heater with built-in thermostat with a convectair. We bought a Convectair without a thermostat for which I wanted to hook up a programmable wall thermostat. The new convectair instructions only say to hook...
Hello everyone ?
It's totally confusing for me. It is my understanding that the neutral and the ground busbars should be connected at the main distribution board (schematic attached), but not at the auxiliary or sub panel. But why?
I know that if I connect them in sub panel the current from...
I have installed some lights to a wooden gazebo and the wire seems relatively thin ( the lights are 30 LED 0.6A each. I’m getting an infrared heater which I suspect will have a thicker cable. It would be easy to run a short cable to connect to the light cable to power the heater. Are there any...
I have a 17 way BG consumer unit I have set up with dual RCD. I got the 25mm tail kit, but can work out how to get 2 live tails into the bottom of the main switch to connect to the RCDs. Any ideas please?
Been retired for a number of years and not kept up with the industry hence I'm well rusty, so apologies for that.
I recently moved home and found that the sub-main cable (10mm x 3 core SWA) feeding the garage/outbuilding is connected to the electricity boards meter & service fuse (cutout) via...
I am not a electrician and I need some help. I would imagine this should be an easy one for you guys. I am trying to hook up an indoor air filter that hangs from the ceiling. I cannot find a schematic for connecting to a power source. It is a four wire system. I am not sure if it is a one speed...
Currently I have 4 small low voltage transformers connected to 4 circuits of low voltage yard lights. They are under my deck, and I turn then on and off using switches above the deck.
I want to consolidate those transformers into one transformer...
I live in a three-room condo in Thailand (220v 50 Hz). Our building has a large emergency generator for power outages and I have tapped into the feed via the hall lights (it's meant to only feed common areas). During outages, I have been running extension cords around my living room...
Hey gents. I'm looking to install a masthead amp to the old folk's TV aerial outside their garden cabin. The current setup is a 10 foot long coaxial cable running from the aerial directly to the tv in the cabin. I want to of course install the amp between the aerial and the Power-supply/TV -...
Hi all,
Would appreciate your thoughts on the following.
Customer has a garage CU fed by a 6mm cable from the main CU in the house. The cable exits the house and then is stretched overhead between the house and the garage. The cable is starting to sag and the customer wants it replacing. My...
Hi all, just fitted out 2 storey extension to house and BC asked if new smokes were interlinked with existing smoke on Landing.
Existing is Battery only, do I have to change existing? If so, does that go onto fitting new to Kitchen/hall aswell?
Can't find anything in Building regs.
Thanks,
Kev.
Hello all: First post from a DIY'er.
My daughter, who lives in a Dallas, Tx suburb, has asked me to connect her new electric oven. Her previous oven was gas. I asked her to send me a pic of any outlets in the cabinet opening once she removed the old oven. (See Pics Below) The house was built...
Hello, I have a fairly simple question like in the title of the post.
How to connect Two 9 watt UV lamps to a ballast probably electronic. I suppose electronic will be the best in my case, due to the built-in starter. I have read various sources of information but did not find my specific case...
Hi
Can you please give me some advice. I asked an electrician to fit a ring.com video doorbell 3 to a Byron 761 wiring and chime so the the ring doorbell wouldn't need to be manually changed. He had several goes, but couldn't get the ring.com bell to make the Byron chime ring. He ended up...
Hello there!
Simple question, I have energy meters like those:
https://www.zelec.fr/details-compteur+d+energie+monophase+direct+45a-155.html
this one is on a french website, but the operation is simple. This one in particular uses an optocoupler 27 Vdc for the pulses, but what is the voltage...
Evening,
I'm wondering what is the best way any of you have found for connecting uplighters laid in paving. Elv fittings thankfully, but only a 50mm cutout in the slab so struggle to get a good, watertight junction through. There is a smallish hollow been left under hole in the slab ( a short...
I have basic experience installing switches, dimmers, outlets in my home; I am not an electrician.
My brother recently had a light that was not working and asked me to take a look. I have a basic question about this:
When I connected the hot wire and neutral to the light fixture wiring: the...
Hey electricians. Apologies for jumping on a question first round in but this LED light fixture is driving me slightly insane.
It has a dimming/color temperature changing driver that also runs bluetooth via a remote.
Driver IN has 3 wires:
White - Neutral
1 Blue, 1 brownishpurple - Both...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.