distribution

Recent contents Top users
  1. A

    Low level distribution board located in toilet.

    Hi Guys I need your thoughts on a job which I’ve been asked to quote for. This is a commercial shop and I’ve being asked to install a toilet and hand basin right next to the distribution board. There is a cupboard around the distribution board however this is low-level. Would this meet...
    • Andrews
    • Thread
    • board distribution distribution board level toilet
    • Replies: 18
    • Forum: The Welcome Forum
  2. G

    Hi Ze at distribution board, how would you approach?

    Hi all, Looking to exploit (please) those older and wiser lol. I was asked to extend / relocate a cooker circuit (6mm t&e) and did so no problems. I then started doing the minor works, R1+R2 came in at 0.05 ohms so was perfect. However, I then went to do do an Ze at the board and get very high...
    • Gringoking88
    • Thread
    • board distribution distribution board
    • Replies: 23
    • Forum: UK Electrical Forum
  3. A

    Distribution boards

    Hi guys. Was wondering if I could get some advice on getting 3 phase distribution boards neater. I am not a fan of cable ties though. I loom all conductors together and sweep conductors into the terminals. I was considering panel trunking to get a neat finish. Any Ideas?
  4. A

    Audio Distribution System Recommendations

    Hi All, Was hoping if peeps can give me some advice. I have an upcoming installation, 5 bed house new build and the customer has requested for the full works, electrics, tv, sat, data in every room, 16 channel CCTV (possibly home automation) and lastly mentioned about an audio distribution...
    • alamski
    • Thread
    • audio distribution recommendation recommendations system
    • Replies: 2
    • Forum: UK Electrical Forum
  5. T

    New Distribution Circuit to existing consumer unit

    Do not know all details but Contracts Manager we know has had EICR done (not seen it yet) but the attached garage has a socket in it not sure if it is on ring or just spurred off ring into garage but a plastic 2/4 way PLASTIC consumer unit has been installed fed from this circuit containing 2 x...
    • Toneyz
    • Thread
    • circuit consumer consumer unit distribution existing new unit
    • Replies: 9
    • Forum: UK Electrical Forum
  6. L

    Distribution board question

    Hi I've been looking at a drawing of an installation. It says it's a 4 way 32A HRC fuse distribution board. Way one is a three phase load and has 40A fuses on each of the phases. The second way has 3 single phase circuits fused at 16A Each, the others are spare. Is it me missing something or...
  7. D

    SY cable for distribution circuits and final circuits

    Hi all, Just a question relating to SY cable and the use of SY cable. My boss his carrying out a EICR for a industrial premise and coming across a lot of SY cable. These cables are used for final circuits and distribution circuits. I know that BS7671 list SY cable as non - standard cables and...
  8. K

    Testing a socket in the middle of a distribution circuit.

    First post. I've installed a 6mm SWA cable to a summer house in the garden from the house. Summer house has a cu with a ring and light. I've installed an outside socket in the middle of the distribution circuit. Between the house and summer house. Question. How do I inspect and test this socket...
    • Kelsall McEwen
    • Thread
    • circuit distribution middle socket testing
    • Replies: 29
    • Forum: The Welcome Forum
  9. K

    Query - Distribution Board to Isolator

    Hello! Im an AC/Fridge Engineer just gone Sole Trader. So Im trying to price up an AC install package for Domestic and Commercial Customers and im scratching my head when in comes to the cost of wiring some Twin & Earth from the Distribution Board to an Isolator on the Outdoor unit. First of...
    • kbrew
    • Thread
    • board distribution distribution board isolator query
    • Replies: 29
    • Forum: UK Electrical Forum
  10. Mark1977

    Running of distribution cables

    Hi, I'm looking for some advice regarding running of distribution cable around a warehouse. My client is having a new 200A supply installed but this will be on a different wall approx 20m away from the existing 100A supply. I need to run a cable from the new supply to the existing busbar chamber...
  11. J

    Tests for replacement consmer unit

    Could you tell me whether most of the tests carried out for a Domestic Electrical Installation Report would have to be repeated if a replacement consumer unit is subsequently fitted?
  12. J

    40 Amp MCB supply to a 100 Amp Distribution Panel Help!!!!!!!!

    My industrial unit is supplied via solar power. All the switchgear and mains supply etc. for the solar is in the unit next to mine to which I have no access unless the tenant is in. The landlord has got the supply coming from the solar unit through a 40amp MCB into our main distribution panel...
  13. J

    max demand for flats

    Just double checking calcs if anyone bored! So for a block of 3 flats with no gas services- all flats same. +communal stairs over 2 floors (LED light few small panel heaters) Flat: Kitchen Ring (32a) (32) Ring (32a) (12.8) Oven (20a) (13) Hob (32a) (16.6) Immersion (16a) (16) Lights1 (6a)...
  14. M

    Adiabatic equation on distribution circuits

    Now I know this has probably been covered a few times but I'm struggling to come to terms with my own calculations. I would appreciate it if someone could tell me if my calculations are correct. So basically I've done a periodic and some of the CPC sizes for sub mains are less than half the...
    • moosey86
    • Thread
    • adiabatic cable circuits conductor distribution equation fault minimum
    • Replies: 9
    • Forum: UK Electrical Forum
  15. T

    3 phase distribution

    Hi all, Just an enquiry.. Our company have recently moved factory's. I am talking a very small unit. At the moment there is one TPN distribution board which is at the top end of the factory.. Is there any problem running a 3 phase supply off a 63amp mcb which will feed the new d/b just to keep...
    • Tom Ashcroft
    • Thread
    • 3 phase discrimination distribution existing phase supply switch
    • Replies: 16
    • Forum: Electrician Forum
  16. D

    Distribution Board Height in a Small Cottage - Full Rewire

    Right doing a job for my registration assessment so got to get it spot on. Job is an old cottage but been stripped right out and complete rewire. Am I correct in saying the dB hight has to be at the same hight as light switch? Seems far to low if u ask me.
    • Danny Gray
    • Thread
    • board distribution distribution board floor height rewire small
    • Replies: 15
    • Forum: UK Electrical Forum
  17. A

    RCB or RCBO in a Distribution Board.

    I am getting back into the electrical game after a few years and wondered what peoples thoughts are on the above. I am happy installing fully RCD protected DBs or Split boards but the use of RCBOs I had never seen. What are the main reasons/advantages/disadvantages for using them? I know they...
    • Andy C
    • Thread
    • board boards circuits distribution distribution board fault rcb rcbo rcbos
    • Replies: 20
    • Forum: UK Electrical Forum
  18. L

    Distribution board checks

    Hi I have a question regarding switch boards and distribution boards. We have an existing switchboard and we want to use four spare ways in this to feed three new tp & n distribution boards. One for lighting one for small power one for security services. My question is what calculations have to...
  19. HappyHippyDad

    SWA or tails?

    I know I have started another thread in the past with an almost identical title but this one is asking different questions! The DNO are moving the meter box and I will need to extend the tails to approx 8m. The present earthing arrangement is TT, I have asked the DNO to change to TN-C-S and...
  20. P

    Single phase distribution for small flats

    im in the process of pricing a small flat development (sheltered accommodation/safe house. type thing It's a 2 storey mid terrace. Being converted to 6 bedroom with small en suites. Shared kitchen diner. Initially I told the developer they need a 3 phase supply as electric showers and heating...
    • pbarrett
    • Thread
    • bedroom distribution flats heating lighting phase single single phase small sockets supply
    • Replies: 3
    • Forum: UK Electrical Forum

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Top Bottom
Back