fault

Recent contents View information Top users
  1. C

    Help tracing a fault?

    Hi - just a DIY homeowner here... 1950's house, 20 amp lighting circuit, total of 10 bulbs and one kitchen exhaust fan on the circuit (all led or florescent bulbs). If I use a regular old 15A breaker everything seems to work fine. If I use a 20A GFCI/AFCI breaker one light fixture consistently...
  2. P

    Garage supply

    Hi there. So I put power into my garage but having a few issues. I've connected the SWA from a 32amp breaker in the main CU (See yellow arrow in picture) out to the garage CU which has a 16amp breaker for 5 sockets and 6amp for 2 LED Strip lights. I've earthed this at the garage CU. Plug sockets...
    • P123456
    • Thread
    • fault garage lights sockets supply
    • Replies: 14
    • Forum: UK Electrical Forum
  3. H

    Continuous earth fault

    Hi, We've lived in the house since Feb 2009. We've had a few tradesmen in and out over the years. We wanted to make sure the electrics got properly certified so used a company locally. They said there was no continuous earth so they used 2 radials a 20 amp and something else which will make...
  4. I

    Ring socket fault

    Not getting continuity on r1, rn and r2. But the sockets are working fine, Amy ideas what the issue could be, I'm checking behind each socket.
  5. W

    Earth to neutral fault????

    Hi, I have an old style fusebox and planning to replace (via electrician) with a modern one (wiring was uprgaded by previous owner) and I noticed when removing a spur line to the outside that was not going to pass muster that my multimeter was showing that earth and neutral were connected. I...
  6. K

    Live earth fault??

    So was testing a house today (new build) When I came to testing on of the ring finals in the house, when testing insulation resistance the live and earth legs on the ring are clear but live to the earth on cpc’s on the cooker circuit, other ring, downstairs lights and heating its bang down I’m...
  7. P

    Socket tester showing fault

    Hi, So I noticed a burned out socket, the wires also pretty burned, and back of socket was also, I replaced with a new socket. Put a socket tester on and it was showing a E fault on pretty much all down stairs sockets. BUT soons I put the oven plug back into its socket the socket tester then...
    • P123456
    • Thread
    • fault showing socket tester
    • Replies: 16
    • Forum: UK Electrical Forum
  8. C

    MV Fault Loop

    I've been thinking, do disconnection times apply to MV? Say a fault occurs on the MV system. This would result in 3kv from the MV neutral to remote earth. In theory this voltage would end up on the LV neutral, enter the structure, cross over to the MET in a TN-C-S supply and then energize all...
  9. I

    Tips for Intermittent Fault Finding

    Good evening! Majority of the work I've done over the past 10 year or so has been new build full rewires and rewires of existing premises and because of this there are very rarely any faults to be found when carrying out the testing of the installations. In a very short space of time, I've had...
  10. Michaelp

    Megger MFT1721 FUS fault code

    Today i had the megger dropped from a meter height and is now showing the FUS code. Checked the fuses, Both are good. Contacts look very good. New batteries installed but still get the same code. I did the reset just in case but no results. This Megger is not in the warranty, is quite old and...
  11. W

    Immersor stat fault

    Thermal cut out kept going on immersor stat so changed the stat over, now the new one keeps having the same issue. Any ideas on what it could be?? Could be another faulty stat but I highly doubt that
  12. A

    Hotpoint Oven SA2 540 HIX with Clock Fault and F12 Fault

    I have a Hotpoint SA2 540 HIX with possibly 2 faults The clock keeps going to reset mode and the display sometimes shows F12 The F12 clears if I turn the oven On then Off again. The clock reset is an annoyance, however if I have Auto On set it will cancel it out. Any Ideas?
  13. J

    Prospective fault at the end of circuits

    Does anyone perform a prospective short circuit and, where no RCD / RCCBO, a prospective Fault Current test on the end of circuits on inspection and tests? I get we do ZS, but how do we know that the CPC or Line conductors are man enough for fault currents of X duration? S2K2 => I2 T? Cheers...
  14. littlespark

    Something wrong.. can’t trace fault

    Went to look at this shower today. Customer says it’s not heating up. Tried everything, and I can’t find the problem...... Can anyone suggest what could be wrong?? ?????????? Had you going there, didn’t I. elderly customers very happy with me going out on a Saturday to replace this...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Top Bottom
Back