I had a 4kw system fitted nearly 2 years ago with a Solic 200 to divert excess energy produced to emmersion heater in hot water tank and all was working great until a week or so ago.
First of all PV solar all working OK, and every morning when inverter starts for first time Solic kicks in and...
Hi all, good afternoon.
New on here, so here goes!
Quick question and some advice really!
I have a 12KW three phase immersion heater installed into a hot water cylinder (for commercial premises).
The immersion heater enables and disables via an on site building management system so therefore...
Hi lads,
My client is having problems with her peak and off peak immersion. She claims she isn't getting enough hot water. I turned both thermostats up but she is still having the same problem. They are new elements but I tested them anyway and they are working fine. I'm wondering if the...
A relative has asked me to install an electric shower. He suggested i use an old electrical point that used to be used for an immersion heater, but has now been plated off with a blank plate and the live and neutral wire inside have been taped off with red insulation tape.
I used my fluke clamp...
jonboy2015
Thread
disconnected
fluke
heater
immersion
old
point
reading
shower
tester
wiring
I live in a park home, it has off peak storage heaters and off peak bottom element on the hot water tank. If I just have the three heaters on[elnur 2x1.7 and one 900w combination with convector] it normally works fine although it has tripped once. But if all are on plus the immersion the main...
Hi everyone, need your expertise on hot water tank set up,
theres a large hw tank with dual 2.7kw elements with stats
controller isn't working as micro switch is broken, but house has new ish economy board supplying about 7
night storage heaters but spark-plumber has installed hw tank on...
Thinking of adding an Solar iBoost to my home system but also changing the immersion heater as its been in for about 14 years and no doubt heavily covered in limescale, not even sure it has a thermostat on it.
I noticed that Backer do specific low wattage immersion heaters for Solar. Is it...
SirV
Thread
element
iboost
immersion
new
really
solar
specific
hi everyone, im new here,and looking for some advice on immersion.
My boiler packed up 2 weeks ago, and having problems trying to fix, sort, research a new one.
In the meantime I thought i could use the immersion for hot water.
It appears i dont have one.
I have a normal non condensing, none...
Hi!
I'd just like a quick bit of advice, we have two fused switches in our airing cupboard for the hot water cylinder, one main switch which comes on during the off-peak of our economy 7. The other which is for the immersion. We've stopped getting any hot water from the main off-peak part of...
auds
Thread
green
immersion
other
something
switch
water
working
I have a customer with a 6kW immersion heater and we are trying to find a device which will cope with this size. All the ones I've seen so far are rated at 13A maximum. Anyone know of a device which could do 6kW?
I need advice in regards to connections to an electric boiler with two immersion heaters. At present, there is an on peak switch connected to one immersion and off peak switch connected to the second immersion. The first immersion is not working anymore. I want to connect the working immersion...
Jason63
Thread
advice
boiler
economy
economy 7
element
immersion
needed
switch
using
working
Hi all and thanks in advance for any help.
I live in a all electric flat and we have a hortsman econmy 7 quartz hot water system, recently the off peak immersion went and we have been stuck using the boost for a few days as and when we need hot water. we are in the middle of trying to contact...
bones101
Thread
boost
economy
economy 7
fault
faulty
immersion
landlord
light
system
under
I went to a job that the owner felt was a bodged job. It was basically a radial circuit wired at the start in 4.0mm T&E, and then it goes to a few sockets that is supplying a washing machine and tumble drier. From there it goes upstairs to the airing cupboard where it feeds a single switched...
Hi people
I have been asked to have a look at a house where another firm has put a pump shower 3A and an immersion 3kW on plug tops.
Now having looked at the regs I am of 2 minds... I personally do not like immersions being on plug tops as they don't like being loading for such long periods of...
Hi All,
Got a problem with a big job we've been doing. Firstly, I'm a spark and not a plumber, but the guy we are working for asked me to get a plumber to fit an immersion heater for hot water to wash his horses off.
So my mate who's a plumber installed a 205 litre indirect cylinder, with a...
Afternoon all, I've been looking at getting a solar immersion controller for my solar PV 3kWp array, and although the IMMERSUN and iBOOST look like the prime players, I'm keen to know whether any of you have had experience with the SOLIC unit? It appears to do the same job as the rest, looks...
Launchman1
Thread
controller
device
immersion
power
solar
technology
these
Just discovered the old wiring for the immersion heater. We have very few sockets in old victorian house. The immersion heater wiring was left in a terminal block wrapped up in masking tape!
I changed the old wylex fuses on the CU to use MCB, thankfully I switched the 16A fuse off for the...
Stuart Todd
Thread
cable
immersion
likely
might
old
socket
sockets
wiring
Hi, i have a dual immersion heater element which is being supplied via 2 separate fcu. These are to be replaced with a horstmann E7 controls. The immersion heaters have 2 separate stats, one element is 2kw & the other is 3kw. My question is which one would be for overnight heating & which one...
On dedicated 16amp mcb Wired in 2.5t&e to sfcu (13a fuse) then 2.5mm heat resistant flex. Fuse has popped twice in last 8 weeks etc. Element R 18ohms. all seems ok? Should I just swap sfcu for 20amp double pole switch? haven't clamped to measure the draw yet as didn't have it with me.
Cheers
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.