Hi guys, if a 3 phase board is to be installed, with 250A mains. With 8 32A 3 phase sockets, 8 single phase 16A sockets, 2 light circuits and 3 phase 63A socket on it, that exceeds the 250A. I understand you would have to consider diversity factor etc into it but is that still too much or would...
can I use the above isolator switch with single phase 240V wiring. live neutral and earth?
its the right designed switch for me and also it is the right current rating.
I am unable to take global IR readings on a 3 phase consumer unit, i have disconnected the neutral but when i try to measure the meter never settles and eventually times out.
i have tried 2 meter/s with same results
I have a single phase system that uses 320 amps and 240 volts and I rewire the circuits for 3 phase what size generator would I need and how many amps on each leg
Moved into remote residential site in USA , devestated 3 years ago by tornado that took house, family and all buildings, poles etc. except well building and barn (where I am living for now) only remaining service is a 3 phase that went to well. For about 6-10 months I need to survive here till I...
hello. looking for advice on working on a 3 ph, 3 wire 480 delta that i believe fits the definition of a corner grounded delta. the title of the thread is appropriate because theres only 3 wires marked for each phase and no neutral going into the customers main disconnect switch which powers a...
Dear All,
My tool Carousel crashed last night and when I tried to initialize the Carousel, the Motor just vibrating (shake hard) but not spin. I am not sure if Break, Encoder or Resolver cause the issue.
Please advise.
Thanks,
David
Hi All
Question regarding 2 phase supplies. Came across this at a farm house, supply is in 3 phase and neutral to the main dist board, then from the 3 phase board at the farm house out to the garage is a 4 core SWA. They have taken 2 phases and neutral from a 63amp double pole MCB at the farm...
Greetings
I work for a client who has recently negotiated a bigger supply from the supply authority, the client has agreed with Scottish power to have a larger transformer and feeder cable installed, my part of the works is to upgrade the existing switchgear to accomodate for the new supply...
Hi All
I am new on here and looking for some advice on converting a car ramp to single phase. This particular ramp is sold in 2 versions single or 3 phase. I bought a 2nd hand 3 phase version at very handy money so can justify a bit of spend on it.
The 3 phase version i have has a 2.6KW 4 pole...
Just sat contemplating life and realised i don't think i've ever seen any RCD protection on the boards we maintain/install at work.
I've seen 300mA protection on some section boards but don't recall ever clocking a 30mA in a 3 phase board.
Am i just not looking properly?
Hi guys,
Is there a standard tolerance percentage that should be followed when checking the winding resistance of each coil on a three phase electrical motor?
The general rule of thumb I followed when measuring winding resistance was that each phase winding had to be identical or close to...
I have a 3 phase AC motor that I have hooked up in low voltage it is supposed to connect to a 120v input 3phase 230v output speed controller I just don’t know how to hook it up. I think I have it right and will post some pictures down below but I would like to double check before I plug it in.
Dear all..
May be some body can help me to explain what happened with my generator set module. At my attach picture. According to S2 = P2 + Q2 is not correct. Can some body explain it.
We have got a hydraulic motor/powerpack for leveling legs of a trailer. However this trailer is running off a 15KW inverter, so the motor needs to run off single phase.
The motor has come configured for 3 phase, however the motor plate does say it will run off single phase.
Would i be right in...
HI Guys,
I bought this motor and speed controller used and tried wiring as per the diagram on the side of the speed control unit but the motor will not turn on. I am running it at 220v, when plugged in I do see the green led light up. There is not much info on the internet. But I was able to...
Hi I have a 3 phase 400v motor wired in star configuration it is controlled via a 3 pole 415v coil contactor which is switched simply via a stay put stop ... In for off Out for run.. ( Spanish design ) there is also a single phase fan connected between one phase and the star point of the motor...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.