A spaceX rocket due to be launched saturday with a satalight as a payload has exploded today whilst being test fired . The spaceX rocket are trying to create a reusable rocket with trips for paying passengers into space.
see SpaceX rocket explodes at Cape Canaveral ahead of launch - BBC News
Hi,
i need to some how get a feed to a hot tub in here too...
any thoughts?
i was thinking it may be possible to rip the existing switch fuse out and stick a mini cu in with a 63a MCB and a 32a? I need to terminate some SWA in there too.
i wont go in to the finer details but this is the only...
Evening folks. Just out of interest I wondered what methods you guys are using in lofts / attics to keep your cables out of the mountains of insulation you can find these days?
Are you running your cables under insulation against the plasterboard or are you trying to clip to the roof trusses...
Need to try and replace an old Wylex board, RCD main switch and 6 outlets (for storage heaters), trouble is I've only got 230mm (height) space. Anybody know of a make that could fit?
Hi just installed new tails and moved consumer unit, cables are about 7 metres long they run inside a cavity from meter and i have then clipped on top of loft joists , on one bit though there is a heating pipe so i have gone under and clipped to side of joist.... i realise cables have to be 50...
Hi All,
Just went to look at a job to replace an old consumer unit which is housed in a recessed metal box, which includes the meter and main cut out. (see picture)
The space available for a new cu is only width 290mm x depth 140mm x height 280mm. Has anyone had a similar problem as I'm...
geezza
Thread
advice
consumer
consumer unit
install
metal
new
space
unit
Hi I posted on the site a while ago enquiring about cable sizing for a new supply at a farm house we have, the supply from western power comes into the meter box situated in an outbuilding and then we have a 25 m run of armoured cable to the consumer unit in the house. We want to connect the...
I'm half way through an installation job that I didn't design, and have come up against an oversight that I need a solution for.
The issue at hand is a new kitchen with a cooker and an oven. The original design showed a 10 mm feed for the cooker, with the oven on the ring (hmm). After looking...
Do any of you lads have business premises? Do you feel it gives you a more corporate / bigger business look than the average sole trader who works from home. I have office / storage space and a small retail unit... At the moment it's all bills, but early days so I'm not worried yet.
Cheers
Ste
Hi
Just to make sure I have this covered, how much space do the DNO & provider normally require for the fuse unit and meter? And what is the preferred height?
KR
Mark
dellboy13
Thread
dno
external
install
installed
meter
position
space
I had a panel install done about 18 months ago and i stupidly said it was ok for them to cover the window (only access point to the roof from indoors), but now i know i have made a mistake and I'm looking for a rough ball park figure for the 6 panels to be moved probably about 1m along to enable...
Hi, this subject was discussed a bit back when I was inquiring about best way to fit fluos in a loft space. I was suggesting ceiling rose /flex, jack chain. Anyway many said just screw fluo fittings to the timber. I though OK that's what I would of done years ago. In loft @ weekend to fit fluos...
Does anyone else think that it's a bit far fetched to believe a probe launched 10 years ago, with possibly even older technology can be shot through space 300 million miles, then somehow 'landed and operated' on a gravity free rock hurtling through space?
This is the Western Front Willy...
My friends are ready to exchange their house but have been told they need to either replace the down lights in the top floor ceiling(below the loft) to fire rated spots or get smoke hats for each.
I thought top floor spots didnt need to be fire rated when the is no escape route or livable space...
Hi,
Looking for some advice please.
2 years ago we had an extension completed. Today I have gone to change some light switches in the extension and found that one 2 gang switch has been used with a permanent live coming in to switch one. This then has loop one piggybacked from it. Loop one...
poderoop
Thread
breaker
circuit
home
lighting
lighting circuit
space
switch
these
My name is Maciej Marosz I'm Inentor and Engineer (Poland 34 yo )
I'm looking contacts with people who are able test and prepare
to production my New weapon . I'm ready relocate from Poland to finish tests
In my head exist many small important details.
Actual Magnetic or Electromagnetic...
Hi All,
I tried the "online" quicker method of updating my ECS card as I wanted my shiny new qualifications adding.
after six weeks I looked online it says "waiting for qualified supervisor approval". So I asked why as the approval had gone from a director....no response
After 8 weeks, sent...
Hi,
have a shower connect up, the run to CU is maybe 8 metres, (3036's) but the CU is in a meter cupboard outside.
There is no space to put a rcd unit inside, and not enough room for a henley block..
was going to get a plug in 40a wylex mcb as there is an existing spare way in the CU, go...
I'm running a supply to a garage sub-main via 10mm2 SWA from the supply head cupboard. There not enough space in there for a standard switchfuse, but I can get in a slim din rail enclose for a single 50A MCB.
This would mean the 25mm2 tails would have to go into top of MCB, with SWA gland at...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc