I have been asked about a switch unit in a hall which has a switch for the hall and another for an outside light. After changing this switch to a sensor switch everything is working fine apart from when hall light is switched on it switches the bedroom light on as well.
Any one used one before? Picked up a job with a complete cockup on the wiring of the switching. Basically it boils down that I don't have enough cores to get the two way working...after a bit of googling I found this Vesternet APNT-92 - 2-Way Lighting using Fibaro Relays | Home Automation...
Afternoon people..
Could someone figure out if there is a way for me to connect this up applying to the regs so that I don’t need to pull another strapper over to the other switch.
At one switch I have..
1x feed from DB
1x Switch line to pendant
1x switch line to 5 amp sockets
1x 3 core +...
Hi
Strange thing happening with next door Neighbours TV , when they switch off their Kitchen ELV(12V) down lighters x6 the TV screen goes blank for a second then comes back on , it is if the signal goes ( Sky Box ) then comes back on , the TV itself stays on .
I just do not have any idea of...
We do mainly industrial and commercial work with a small bit of (landlord) residential.
After some recent negative comments from potential customers regarding NICEIC electricians I was thinking of jumping ship to ECA or Napit.
OK I know ECA are now the same as NIC but there name doesn't seem...
I am renovating my own house at the moment and want to bounce an idea off of you all
I need to wire a socket high level on the wall at the bottom of the bed for a tv on the wall. I want to be able to switch this off as the tv has an anoying led that lights up the room. Im going to install a...
Good evening all. Despite of being utterly ignorant on the subject, I have an issue which tickled my curiosity and would like some assistance to understand.
I have a printer (although I'm pretty sure it doesn't matter what appliance it is) that, sometimes, doesn't switch on. After numerous...
I thought folk might be interested in the Zellweger mains signalling system which I discovered yesterday. My sister wanted to know if she had economy 7 electricity in her rented home. She described to me the intake which as well as the cutout, meter and CU included a 'small black shoebox'...
Hi all....
Quick question for you, what are your thoughts on the above?
I am looking for an alternate way to operate a bathroom extractor fan (don't want it on with the lights and don't want extra pull cords etc) - I propose to fit an inline fan in the loft, switched with a microwave sensor...
Hi everyone looking for a bit of advice.A friends mum wants to add a wirless 2 way switch to an existing 1 way light ( nice wallpaper not wanting to chase walls) . I can get to the joint box but just not to sure what wirless switching is available and any good for job. Any advice...
I have a Fully pumped S plan with two zone valves HW & CH, when the programmer is off, the room stat is turned down as far as it will go the heating still comes on, I'm assuming the CH 2 port valve is faulty and must be letting voltage through to the pump/ boiler. I have two valves a drayton...
Hi All
I was replacing some faulty fluorescent lights yesterday when I cam across one with an emergency light attached to it. It was non maintained as once I had isolated power it switched on. When I cam across this light I could see it was an afterthought as the original light was wired in old...
I'm changing 4 spotlights over to LED and the spotlight which has all the switch wiring in is the only one switching on/off at the switch.
I have identified the switched live but I am obviously missing something as the other 3 are permently on and will not be switched off at the switch.
Any...
installed a tub for m8 (second hand).
switch on tub runs for about 10 seconds then trips.
clamped up draw initially 3.3A -12.2A when heater kicks in.
disconnected heater unit IR test 400M ohms, 23 ohms heater resistance.
disconnect pump one hot tub will stay on, disconnect heater & leave...
Been to fit new led pir flood. 3core +e. Perm live. Sw live. N e.
Flood is 2core. So wired it perm live set up works a treat. Customer rings up wants it on switch. After investigating switch is a 2 way.. any way of doing this so works on pir then on with switch.
It's a sealed led...
Hi, I recently purchased an espresso machine that the previous owner said he couldnt remember how to wire after taking it apart for cleaning. So after a few days of not finding much relevant information on the machine or the control board, I spent the next few looking at datasheets and visual...
Back again!
Im currently doing some garden lighting at my parents place and need some help on the switching arrangement. I ran all armoured's(9) back to the garage and connected them to a din rail enclosure, from this enclosure i ran a 12core armoured to the house via adaptable box. The...
Hi all, first of all sincere apologies for the lack of experience and inappropriate use of symbols! I'm putting together a remote mobile broadband station for use at events that can take a mains supply (transformed to 12v DC) or leisure battery.
I've obtained a 12V switching relay which works...
Hi
I’m thinking of switching to a Hive 2 thermostat …..
I currently have a very old SUNVIC TLX thermostat which from what I can work out is only connected to the oil central heating circulating pump which it turns on and off..
There is also a thermostat on the electric hot water cylinder...
pspec
Thread
boiler
electrical work
hive
switching
system
thermostat
thinking
water
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.