Hello everyone
I'm picking up some remedial works from an EICR fail in a commercial property.
Its a 3 phase supply with old steel conduits , trunking & coupled metal equipment, that provides the earth to the various locations.
At present the earthing is insufficient, every earth in the...
just a quick question about galvanised trunking in a commercial setting with regards to an assaignment ive been set by my college.
i have got a run of trunking running from a plant room in a car garage which will carry pvc singles for sockets lighting etc, alongside this i have to get 4 cat 5's...
Just doing a re-wire on a community hall/scout hut. There's a actually a surprising amount of cable gone into a 25 x 10 m one storey building. 6 x 3kw heaters, sockets everywhere, water heaters , LED Panels, downlighters etc etc.
All cable runs are being done in the loft space and due to the...
Hi all and thanks in advance for any replies.
I was wondering if whether when having more than one phase inside a dado trunking are you required to mark up the trunking with a 400v marker/label like you would at a multi gang light switch??
Cheers
Hi
Just looking for some advice. I've had a new supply and meter fitted on the outside of a building. The supply is for a new consumer on the first floor. The meter tails for this have been run down the outer wall. What trunking would you use to protect these?
Many thanks
Hi. I've recently moved into new house. The meter box and consumer unit are installed in cupboard underneath the stairs, however they are approx. 1.5m apart and the tails are surface mounted. Should they be encased in trunking so as to protect them from damage. Thanks
beanocur
Thread
build
meter
meter tails
stairs
tails
trunking
under
So workshop with perimeter 75x 75 galv trunking, with overhead lighting trunking suspended from rod with hangers, lighting trunking is quite a bit higher than the perimeter trunking, how do you link the two?
Would you use an internal bend and flange it down onto the trunking at either end? Or...
hi
just wondering which brand of trunking do you guys generally use. would you say all trunking is the same? i usually get the stuff they have a tlc or screwfix and to be honest don't notice much difference (except tlc trunking is in 3m length whereas screwfix can be 2m)
is there any trunking...
Electricians Required
call Brian Taylor on 01698324664 or email [email protected]
Long term contract opportunity with Global Infrastructure Service provider with £100 million plus turnover!
Working as part of the internal mains division, running new connections to multi domestic sites across...
Hi there,
I was just looking to find out what would be the most appropriate reference method to use.
the distribution circuits leave the fuse board in 3 meters of trunking, then onto basket most of the ciruicts at lower lever then come down the wall in conduit which has been pre installed in...
Just removed from site.
19 x 2mtr lengths Telemecanique KBA 25EA402 lighting trunking.
118 x 3mtr lengths Telemecanique KBA 25EB403 lighting trunking
9 x Left hand Feed units Telemecanique KBA25AA4
105 x Telemecanique KBC 16CF21 Tap off boxes
36 x Telemecanique KBC16CF40 Tap off boxes...
Just removed the following from site ,
19 x 2mtr lengths Telemecanique KBA 25EA402 lighting trunking.
118 x 3mtr lengths Telemecanique KBA 25EB403 lighting trunking
9 x Left hand Feed units Telemecanique KBA25AA4
105 x Telemecanique KBC 16CF21 Tap off boxes
36 x Telemecanique KBC16CF40...
Hi,
If you have a luminaire connected to busbar trunking via a fused "plug" is this then considered as a fixed appliance? And if so, if you were to change that luminaire would that constitute an change to the circuit, i.e. Would you need to issue a MWC? I am also assuming that if the plug is...
Hi,
I've got a job coming up that involves networking an underground office. The walls cannot be chased and the Ethernet sockets need to mounted on the wall. I was thinking of running the cable in trunking but I don't think it'll look professional, then thought of using conduit but not too sure...
Hi Guys
No doubt this has been asked before, and the answer is already out there somewhere but I'm tired and the job is tomorrow so please bear with me.
Existing CU is back entry, spaced off the wall by an inch on a couple of vertical battens in a tight wooden cupboard. I'm intending the same...
Piratepete
Thread
cables
change
consumer
consumer unit
entry
requirement
trunking
unit
For cables coming out of a CU and running where someone getting tools on and off a shelf next to the CU may knock against the cable if careless. I'm intending to give them some basic protection by putting trunking over them. The cables coming out the side of the CU go through non-combustible...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.