verification

  1. P

    Do you test the suppliers earth conductor for continuity??? (Initial verification)

    Hi guys, QUESTION: Do you test the suppliers earth conductor for continuity??? The guidance note 3 2.6.5 refers to regulation 643.2.11 which requires a continuity check be carried out on all protective conductors including: EARTHING CONDUCTOR, CPC's and bonding conductors. I am aware of the...
  2. A

    2396 design and verification

    Evening folks. Does anyone know how many Mark's you require to pass the written exam. Or if anyone would like to share their experiences on the course and the exam itself.
  3. A

    Initial verification question

    So I've got my 2391... and was always taught and was under the impression that when carrying out R1+R2 tests on all circuits you must carry out the test at all points on the circuit, not the furthest point or a selection of points, I thought the test was to A. Prove a earth path that is suitable...
  4. Gary Tollison

    Earth fault loop impedance, initial verification, multiple DB

    Hello. Not sure if this is the correct forum to post this in (still trying to work out where the trainee section is). Just been doing some practice fault-finding online. Found this scenario: After doing initial verification on an outbuilding with its own DB, which is supplied from the main DB...
  5. M

    Another play for companoes

    Hi . I have just been informed by a main contractor that I do work for that i need to register with RESET . This is a system for verifying that workers are fully qualified and holds all all workers info skills training QUALIFICATIONS disclosure etc all under 1 roof. As a member of safe...
  6. Daniel Jones

    2396 style question, 2400, short circuit, RCBO,

    hello, studying for my 2396 exam and i need some help! Been banging my head against a wall for hours trying to get this one straight in my mind. The question is as follows: An electrical installation within a small retail outlet, located in a farm building is to be designed with the...
  7. AyresomeBoro

    City and Guilds Design, Erection and Verification (2396)

    Looking to do this course in the new year. Absolutely no-where in the North East delivers the course so looks like I'll have to take a week off work and stay over somewhere that does! Can anyone recommend a decent place to attend? The closer to the North East the better as I assume I will need...
  8. gatuka

    pass mark %

    does anyone know the pass mark for initial verification
  9. T

    2394 course - advice on what I can do afterwards

    With the 2394 qualification can I pass my own work or do I need to take the 2395 as well. Anyone know of good places in London where to take this course -how much did you pay? Thanks.
  10. G

    Best training route

    Hi guys, im im new to the forum and just wanted some advice on what the best training route to go down was. I have just completed my NVQ level 3 (marine fitting bias) and will in September be starting my HNC in electric and electronic principals. My aim is at some point in the future to join...
  11. J

    confused

    I want to do the 2391 but been told its in 2 parts 2394/2395 now here come the confusion Do i need both parts or is just doing 1 ok cheers
  12. K

    RFC using conduit as cpc

    What is the best way to confirm r2 and R1+R2 when the circuit is routed in conduit and this is used as the cpc? I have used wander lead and got continuity at all points on the circuit for the cpc. rn and r1 are within 0.03 of each other so no problem there. just how to confirm that the...
  13. B

    City and Guilds Design and Verification...?

    All I am hearing of late is that the 2391 is going to be scrapped and made easier and the 2330 is being scrapped and being renamed something else. Does anyone know if something similar is going to happen with the Design and Verification course? Is there anywhere is South Wales still doing it...
  14. 3

    Design Software

    Hi, Im new to this forum and this trade for that matter. I have been working as an electrician previously but gave it up some time ago, only to get back involved this year. I am taking the exams at the mo and am quite interested in the design side of the trade and wondered if anyone had any...
  15. C

    Help for testing

    Hi I work on building sites and obv we have to test all of our installations but we have certain people who end up testing but I wud like to learn, do u knw of any books that I cus get that break testing down and explain wat to do and how in very simple terms
  16. shakerbess

    2400 city and guilds past papers

    hi im hoping to under ake the 2400 design and verification course was hoping for past papers or if anybody got course material they could forward to me please
Top Bottom