Discuss UK light wiring in the UK Electrical Forum area at ElectriciansForums.net

wallis2xk

DIY
Reaction score
0
Hi,

I'm trying to replace a light fitting and am unsure of the wiring here, which must be quite old. There was a red going into what I presume is earth, but then a double black wire and a single black wire. Are these Neutral and Live?

Thanks
 

Attachments

  • Screenshot_525.png
    753.8 KB · Views: 39
  • Screenshot_524.png
    722.4 KB · Views: 40
The three reds are all Live but shouldn't be connected to the light. They need enclosing in a terminal block or a wago connector.

The two blacks twisted together are neutrals and should be connected to the light.
The black on it's own will almost certainly be coming back from the switch and is the Switched Live. It should have red tape or sleeving around it but a lot out there don't. That is the Live feed to the light.

The greens are earth and should be connected to the earth terminal on the light by a single wire sleeved in yellow/green.
 
The old fitting uses the third terminal as earth or loop, look carefully you can see it stamped and in your case it was used as a loop for the three reds. Personally I would get a complete new fitting which incorporates all terminals to the base unit, like this.
https://www.NoLinkingToThis/p/british-general-straight-batten-lamp-holder-bc-3/93835
 
Thanks for the replies. @westward10 I have indeed got a new fitting which I put on the right of the photo with the casing removed. So is there any issue if I wire the new one the way it was before?
Reds -> Earth
Double Black -> Neutral
Black -> Live
 
Last edited:
The reds should not go to that terminal as it is identified as earth. Can you show the rest of the new fitting.
 
@westward10 Ok thank you, I'll get one of those. Excuse my ignorance again, but just to clarify, the red wires could go into the terminal into the the old fitting because it could be used as loop whereas on the new one it can't be used as a loop?
 
Not all batten holders have that 3rd terminal but those that do, sometimes have it connected to the metal shell of the bayonet socket as a means of earthing (or at least, not thoroughly insulated from it.) Therefore, if the reds (permanent line loop-through) are connected to the terminal, it makes the metal cap of the lamp live to the touch, even with the switch off. The light works, of course, and you only find out when you happen to touch some earthed metal while changing the lamp. Some types of fitting have an isolated terminal that can be used for the line loop-through, but only if it is specifically marked as such, as your old one was. It is conventional to place the three red wires in a separate terminal (and the CPCs likewise if there is no earth terminal on the holder) but the enclosed type with terminals integrated into the backplate pictured by @westward10 is a much better idea all round.
 
Last edited:
How is this sort of outdated rubbish still allowed to be sold?

Probably should explain further for the OP.
It is not permitted to connect wires insulated with 'ordinary' PVC (as in your cables) directly to a lamp holder. The final connections should be by wires insulated with a high temperature resistant plastic, such as the short blue and brown wires on the one in westward10s pic.
 

Reply to UK light wiring in the UK Electrical Forum area at ElectriciansForums.net

Similar Threads

First, sorry if I'm not in the correxct thread. I'm trying to replace an old switch with a WIFI switch and cannot seem to do it right. There are...
Replies
1
Views
263
Hi, I'm replacing a light fitting in the bathroom but the wiring is confusing me, black brown and grey? Is black neutral and brown live in this...
Replies
14
Views
2K
I bought this house a couple months ago. It was built in 1952 (same as me) but has been rewired with yellow 12 awg Romex dated 2007. Looks like a...
Replies
7
Views
493
Hi, have an old bathroom fan. Which has two wires the black and red (line and neutral). The fan has no isolator switch and was powered when the...
Replies
3
Views
615
Hi I am trying to replace my old white light switches for nice chrome ones but the wires are all red but the new switch has only l1 l2 top and...
Replies
6
Views
656

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Electrical Forum

Welcome to the Electrical Forum at ElectriciansForums.net. The friendliest electrical forum online. General electrical questions and answers can be found in the electrical forum.
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock