10mm

Recent contents Top users
  1. B

    testing the water.. 50mtrs 10mm t&e

    I might have 50mtrs of 10mm T&E for sale brand new still sealed, depending on price, I may keep hold of it for future use. £75 collected, £100 posted? offers.....:bucktooth:
  2. L

    10mm SWA

    Hi, My regs are in the van and it's peeing it down :cry_smile: 10mm SWA 3 cores, for single phase supply, clipped direct 67a or is it 58a? never remember. Lets hope I have a 50a MCB in the van for tomorrow
  3. S

    10mm bonding

    done some new flats incoming water is in plastic in kitchen and point of entry of gas pipe is at the boiler in each flat so we have 10mm bonded the boiler ,gas meters are all in basement carpark communal cuboard and plumber wants meters bonding or his sticker book comes out. not a problem to...
  4. K

    10mm single earth

    Has anyone got any idea whether bonding cables can be buried direct in screed? Iv been putting my mains cables in conduit on the floors but wondered whether to just zip tie it to an existing run of conduit i have going in the right direction, can't find anything in my books on this
  5. W

    10mm Twin and Earth

    100 Metres for sale .. open to sensible offers :-)
  6. W

    Re: Will a 10mm PYRO take 80 amps :):)

    This thread on the 'General Forum' has to be a wind-up. What sort of person would go into print with suggestions like this:- "The DNO fuse is too small - So shall I change it for a bigger one" ???
    • wildgoose
    • Thread
    • 10mm amps pyro
    • Replies: 1
    • Forum: Electrician Talk
  7. S

    Will a 10mm PYRO take 80 amps ?

    Hi, I need to change the main incoming fuse from 60A to 80A but there is a 10mm pyro feeding the property and i dont really want to replace this. The reason I need to up the supply to 80A as I am installing a sunbed which runs at 40A single phase. The load will never constantly be running at...
    • sycamore89
    • Thread
    • 10mm amps pyro
    • Replies: 31
    • Forum: Australia
  8. P

    Buried 10mm cpc

    Hi guys,Is it ok to sink a 10mm CPC to a oil tank in a bit of duct under a patio about 4m in length?CheersPaul
    • Paul Chick
    • Thread
    • 10mm buried cpc
    • Replies: 6
    • Forum: Australia
  9. D

    10mm armoured need replacing?

    I have a 10mm 4 core glanded into a length of conduit buried in the wall, around 2 metres in length, I tested continuity between all cores and galv conduit and it's perfectly clear, however when I tested IR it failed between 2 cores and conduit. Am I missing something here or does it simply need...
  10. sythai

    Thoughts on this please...? 10mm tails !!

    Just seeing what others would have done ? New kitchen install ===> 2 x 4 way wylex rewirable CUs - 1xlights 1xpower (sketchy wiring / can of worms) ====> SO ====> henleys + split tails + mini cu for kitchen install (simples:smiley2:) My only concern is the 2 existing CUs are supplied via 2 x...
    • sythai
    • Thread
    • 10mm please tails thoughts
    • Replies: 8
    • Forum: Australia
  11. H

    10mm Earth Cable burnt

    Called out to a house this evening. Rewireable 32A fuse blown and the 10mm earth cable between the main earth terminal in the consumer unit and the TNCS connection at the cut out completely melted. I checked ZE and PFC at supply and replaced the earth cable to the unit. Hadn't got time to...
    • Happyneiller
    • Thread
    • 10mm burnt cable earth
    • Replies: 14
    • Forum: Australia
  12. DaveyD

    PERSON stole my 10mm bonding

    So over the weekend some little <S> pikey</S> tike snipped the 10mm bonding that was not in conduit from the garage. I am now 4M short and the rest is all done (although the circuits are not energised and this is for a new gas supply that's not yet fitted so it's safe). Its quite a long run -...
    • DaveyD
    • Thread
    • 10mm bonding person
    • Replies: 27
    • Forum: Australia
  13. J

    6mm or 10mm to an electric shower ?

    had a job last week ,the company i work for use a contractor now and again for jobs we dont have time to get to . the deal was they would run in a supply for an electric shower up to the isolator and when we are ready we would come in and remove bath , install shower cubicle and shower . after...
  14. H

    Looking for 10mm Green/Yellow,Blue,Brown in metre lengths.

    Hi everyone, I nipped over from the Plumbing forum where I usually play to ask if any of you can offer any assistance. I am in need of 10mm2 Conduit cable wire in the following colours, Green/Yellow, Blue and Brown. I checked Screwfix and EL Electrics in my local area and did some searching...
    • hussy
    • Thread
    • 10mm lengths looking metre
    • Replies: 15
    • Forum: Australia
  15. K

    10mm chuck

    got the new bosch 10.v drill the other day, does anyone do an arbour that will take a 63 mm holesaw that will go in a 10mm chuck?
  16. Richard Burns

    TNCS 10mm existing Earth OK

    Quick question regarding Earthing conductor sizing. I have just done a job on a TNCS supply with 16mm tails which has a 10mm earthing conductor, adiabatically this is OK and meets the requirements of 542 and 543 (but not 543.1.4). However I had in mind that TNCS minimum earthing conductor size...
  17. C

    bonding gas and water how do you work out when to go up from 10mm to 16mm and so on

    were currently doing a job in massive old pub whats going to be a libary, my gaffer says put 10mm bonding to gas and water but how do you actually work out what size is required
    • chopper
    • Thread
    • 10mm bonding conductors earth electrical work gas neutral out water when work
    • Replies: 37
    • Forum: Australia
  18. sythai

    Joining 10mm to 2.5mm T+E

    Another joining cable thread..... Just curious how you chaps would have done this ? 10mm ---> 2.5mm T+E, adaptable box will be permanently accessible after (re-using old shower supply) Sy:smug2:
    • sythai
    • Thread
    • 10mm 2.5mm joining
    • Replies: 9
    • Forum: Australia
  19. A

    Extending a circuit in 10mm t&e

    Can anyone advise the best way to extend a circuit in 10mm t&e please. I have used crimps for 2.5 but I understand this is not suitable ? Thanks
    • Arghhh
    • Thread
    • 10mm circuit crimps extending please t&e
    • Replies: 12
    • Forum: Electrician Forum
  20. M

    10mm earth bond

    is it ok to through crimp 10mm earth bonding cable due to relocation of board. would re run new cable but under tilled floor. thanks
    • mcm
    • Thread
    • 10mm earth earth bond
    • Replies: 7
    • Forum: Australia

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Workwear Shropshire
Top Bottom
Back