bath

Recent contents Top users
  1. A

    Whirlpool Bath

    I have had a call from a guy who is looking at installing a whirlppol bath, i have not seen the bath or house or instructions but my first thoughts were an fcu outside the bathroom connected to the upstairs ring, then I thought what if its an old system with no rcd protection? so i thought rcd...
  2. S

    Shocks from Bath tap

    Hi Guys!! Long time no speaky. I've come across a problem that I need a little help with. My colleague was called out the other month to a house where they kept getting shocks off the bathroom taps. He called me up for some advice over the phone and we found out that the main bonding was...
  3. S

    anyone got a bath

    I am in need of a new bath as I broke nine last night (nothin to do with my weight) I had a slight accident after a lemonade or 2, so if anyone in the northWest area has or knows of a bath going cheap then I would be very grateful. Thanks
  4. R

    Bonding to a copper bath

    House has 17th ed board. Bonding in place. Do i need to bond the bath. What testing would you recommend
  5. T

    RCD for assistted bath

    Hi. Situation: A new reitirement home has assitted baths installed in twin & earth with 50mm depth and with ceiling mounted pull switch. The supply is under the bath enclosure and is hard wired. Keeping in mind the controls will be handle by a skilled person (nures etc.) The circuit chart shows...
  6. A

    Structural roof surveyor in Bath area

    Can anybody recommend some good (and reasonably priced) roof surveyors in the Bath area. I'm required by NAPIT to have one done for a solar installation. Thanks
  7. D

    Supp bonding to a bath

    Hi lads Could someone please remind me of the requirements for supp bonding in a bathroom which has all circuits RCD protected, not got a regs book to hand. Many Thanks
  8. S

    Jacuzzi bath, replacement LED light

    Just a quick one Im having a blank moment Jaccuzzi bath, all protected by 30mA RCD. One light fitting to replace, its metal bodied, 2W, double insulated 12V It has a point on the back to bond to..... You know what Im going to ask don't you! Does it need to be supplementarily bonded to the...
    • SPARTYKUS
    • Thread
    • bath bonding led led light light metal moment replacement required
    • Replies: 3
    • Forum: Electrician Talk
  9. T

    Intake behind bath taps

    Anyone ever seen this before? The intake at the back of the bath just behind taps, and fuse board just above bath taps in a cupboard.. Would you code this? It's hard to see there but there's the supply cable coming up from floor, a 6mm earth onto the armouring, then tails from the cut out, this...
  10. R

    socket in toilet no w/basin, or bath or tap or shower!!

    Hi guys, My common sense says that if there is no tap, w/basin, bath or shower i.e. just a toilet, then having a double socket on the wall at 230 cm high position should be ok. Any suggestions or comments please?!!
  11. B

    Shaver socket very close to bath?

    As the title says. The shaver socket has been 1st fixed on the right hand side of the wash basin, but due to the close proximity of the bath, the shaver socket falls just inside the edge of the bath.Wil this need to be moved? If so how far?
    • BillyH
    • Thread
    • bath close moved shaver socket zones
    • Replies: 3
    • Forum: UK Electrical Forum
  12. P

    Shower pump under bath

    Hi Guys First post here, I am a plumber and have been asked to change a shower pump which is currently sited under the bath. It is fed from a fused spur screwed to the floor under the bath. I want to know where I stand with the regs in regard to changing the pump and joining onto the fused...
    • plumb1
    • Thread
    • bath isolation panel problem pump shower under
    • Replies: 9
    • Forum: Australia
  13. M

    Height of shower over bath

    Hello everyone Need a bit of advise I have been asked to install a bath in a room that was previously a wet room for a disabled person. Now as per usual the customers don't want to spend a lot of money. At the moment there is an electric shower installed at a height of approximately 750mm to...
    • Mfctitch
    • Thread
    • bath electric height installed instructions manufacturers shower
    • Replies: 2
    • Forum: Australia
  14. R

    Sockets in a room containing a bath

    I came across a rather nice bedrrom the other day which also had a bath in it, it was kind of an extension off the bedroom, but no door or partition. Sockets in the bedroom end were closer than the 3 meter reg. What would this be coded (if any?) if a PIR was carried out. Wiring was in the new...
  15. M

    water heaters above bath in zone 1

    a periodic report reports that a water heater is not allowed in zone one. the 2.5 supply cable is clipped direct going into the bottom of the heaters. the heaters store more than 15 litres. regs wise whats the deal. how do i make them comply without moving them. rcd yes but what else? thanks
    • Mike Watters
    • Thread
    • bath heaters water zone
    • Replies: 12
    • Forum: Australia
  16. A

    Down lights above bath?

    I currently have 240V IP65 down lights in the ceiling above my bath. I'm in the process of fitting a wall mounted shower head which will be very close (200mm) away from the ceiling down light. Is this ok? For info the circuit is RCD protected.
  17. L

    Bristol / Bath PV Installers

    Hi , I am going through the NIC MCS audit in late October and would like to get a bit more experience so was hoping to find an Electrician in the Bristol or Bath area ( i live in Keynsham and have a yard in Oldland) who would be willing to let me help out on a few PV jobs (free of charge of...
  18. S

    Bath and shower with 13amp plugs ????

    Just done first fix on a new bathroom and customer has a new whirlpool bath being installed and a steam shower very fancy and both with radio etc etc. However they have both been purchased on web from abroad. Both have come with creepage protectors fitted inline with a 13A plug on each. My...
    • sidekick
    • Thread
    • bath current electric plugs remove shower
    • Replies: 9
    • Forum: Australia
  19. P

    low voltage ip44 leds in bath panel??

    Hi , just want your thoughts on this , tiled bath panel sealed , with ip44 leds in the tiles, wired from existing switch , switch powering socket in loft lv transformer in plug pluged into skt and wired to leds in bath panel, psc current of low voltage? because there is no earth in the lv...
    • pierce
    • Thread
    • bath led leds low voltage panel voltage volts
    • Replies: 5
    • Forum: Australia
  20. P

    Whirlpool Bath

    Hi guys, what are the regs on the location of a fused spur for a whirlpool bath? Thanks
    • Paul Downham
    • Thread
    • bath
    • Replies: 3
    • Forum: Australia

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Workwear Shropshire
Top Bottom
Back