cutting

  1. Lister1987

    Cutting conduit, I hate it already...

    Any tips for cutting conduit to ensure a good finish? We're starting with it at College and I hate the stuff, I end up cutting to length fine but after touching up it's all buggered. Unfortunately due to my cerebral palsy, my fine motor control is pretty shot, along with my ability to judge by...
  2. O

    Jumper keeps cutting out faster progressivly

    Hi all, thank you for reading my post. My first one so I hope it is in the right spot. I just bought a house in Thailand. I moved in a week ago and 3 days ago a jumper started cutting out. Since then it has been doing so more frequently and now I am unable to put it in the on position. I am a...
  3. B

    RCD cutting without physically tripping. a

    Hi I’m new. I have a flat in Madrid which was re-wired in 2011. The fuse box has a single pole 25A breaker, plus a 2P 25a breaker. These feed an RCD known here as a “diferencial”. When I use the oven plus hob plus aircon the power goes off but none of the consumer unit switches physically trip...
  4. EalingBadger

    Opinions on the best diamond discs for cutting concrete

    I need to cut several tens of metres of 100mm x 100mm channels in hard (it's a C40 mix) concrete. Some of these channels will be for electrical services, some for other services (mainly MDPE water pipes) and some cuts will simply be to assist in tidying up a bit of a scruffy concrete pour. I...
  5. Stephen Tromans

    Electric combi boiler keeps cutting out.

    We have a 5 years old EHC combi boiler which switches the central heating off now and again ( no pattern that I can see ). To get it working I switch through the programme options once or twice and it starts up. It can be ok for weeks or days. Can anyone suggest what is wrong with it please...
  6. E

    LED downlight issue 1x keeps cutting out

    Can any one help? Just been to a customers house and in a loft extension there are 6x LED downlights (cob). The last downlight in the circuit seemed to be cutting out when the dimmer was at the minimum so I replaced the standard LED for a varilight dimmer so the minimum could be adjusted...
  7. Tallman

    Spur circuit cutting out then restoring - no RCD trip

    This is a new one to me.. a small spur circuit (3 double sockets) on ground floor, several small load items connected - table lamp, assorted AV kit (TV, Amp, DVD). On just these 3 sockets only, the power cuts, sometimes flicking on - off - on again. Other times it'll stay off for 1-3 minutes...
  8. G

    Cutting 5 inch ventilation ducting

    I’ve got to install flat and round 5 inch pvc ducting on quite a large scale, I’m currently cutting it with a grinder but it kicks up a lot of debris and it’s hard to get a square cut, hack saw is better but slow. I reckon I need a cordless chop saw. Anyone else got one for cutting ducting and...
  9. N

    Boiler cutting out/tripping

    Hi all, first time on here and I need some advice please. My boiler keeps tripping. After the original boiler installers came to fix it and declared the problem was due to faulty electrics, I had it rewired onto its own RCD circuit, and it was fine for a while, but has now tripped every day for...
  10. T

    Power Keeps Cutting Out After New Fuse Box Installed

    Hello everyone and thanks in advance for any advice. I hope this is an appropriate place to post this thread. I live in a council flat and had a new bathroom fitted some months ago. A new fuse box was installed at the same time. Ever since we have had problems with the power cutting out...
  11. Leesparkykent

    Nylon snap in bush

    Any one know a supplier of these? looking for 25mm and 20mm as have a few new builds that are all metal portioning...Fed up of using grommets. cheers
  12. G

    Hardend steel, what cutter?

    HI all, got 15 x downlights to install in a soffet, its got wood under it and also about 3mm steel plate above, my usual ck or starret cutter wont even touch it, ive have drilled one out with a series of holes but it was a nightmare, any hardened cutters out there that might do the job? CHeers...
  13. J

    Cutting 300mm hole in lath and plaster ceiling?

    I have to fit a condensation control fan (PIV) into the hall ceiling. The hole needs to be about 300mm and the ceiling is lath and plaster! Any tips for cutting the ceiling without damaging the surrounding lath and plaster? Cheers
  14. Startinez

    Tips for general "DIY" aspects of electrical work

    Hi all, I am training in domestic electrics and employed working in a commercial basis on D.C systems for telecommunications infrastructure. Because of this, I don't have much time to actually get experience in certain aspects relating to electrical work such as cable chasing in a domestic...
  15. R

    Bosch Metal Cutting Circular Saw.

    I have been searching for somewhere in the Uk which sells the Bosch CSM180 metal cutting circular saw, without success. The yanks have had it for a while now, but I can't find it anywhere in the UK, I would like to know, has anyone out there seen it here??? All my 'stuff' is Bosch and I would...
  16. O

    Cutting corners or acceptable practice?

    Saw this today. Apologies for the carp photo. Its the use of Wago's connecting the under cupboard lights! Acceptable or not? Personally I wouldn't do it!
  17. Midwest

    Cutting off Moulded Plug Top from appliance

    Some of you might have read a thread where the OP was asking about cutting off moulded plug tops from Velux windows; http://www.electriciansforums.co.uk/electrical-forum-general-electrical-forum/109817-electric-velux-window.html I personally had been advised by Velux, in doing so would...
  18. D

    Floodlights Cutting Out

    I work at a small sports park where we have a grass football pitch with 2 sets of 7 2kW floodlight heads per side and a 3G pitch with 2 sets of 4 1kW floodlight heads per half. Each set is on its own switch which control relays. All run at 400v. My issue is, once every few months one side (x4)...
  19. F

    Cutting Slots In In Metal Dist Boards

    hi lads what ru using to cut slots in metal dist boards consumer unit my old jigsaw has justgiven up on me many thanks paul
  20. A

    Ck Trunking cutter views

    Anyone have any view on this product , seems to have descent reviews on Amazon , any of you with experience with one ? Previously owned the red version liked it very much , just wondering if there's anything that might be better

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock