fuse

Recent contents Top users
  1. HappyHippyDad

    New supply to garage. DNO have not fitted fuse.

    My customer has had a completely new supply installed to his garage. The DNO has not put a fuse in the cut out though. I'm guessing he needs to contact the DNO to discuss? I realise it would be very easy to pop a fuse in, but apart from this not being allowed, I also wouldn't know the size of...
  2. E

    Fuse missing from main disconnect panel

    Hi there, I run a recording studio out of an early 50's built warehouse. I've been having electrical noise and ground loops in my audio equipment since I've been here (almost a decade) and I've finally decided I can't deal with it anymore. I'm going to install a new main panel as well as new...
    • Elvisbeehive
    • Thread
    • disconnect fuse main missing panel screwfix
    • Replies: 4
    • Forum: UK Electrical Forum
  3. S

    LG 42LG3000 fuse keep blowing issue

    Hi all. i have an issue with my LG 42LG3000 TV. Yesterday I was watching a movie and TV suddenly turned of and there was a strange sound. I have decided to change the fuse(3A) and it happend again after putting a plug into a power socker - again fuse blown. I know that TV was bought around 12...
  4. Aaron b

    20kA ipf on 15A 3036 fuse

    Hello, I changed a socket over earlier and tested the circuit after. The fault current was 20kA, Am I right in thinking I only need to consider the breaking capacity of the service fuse that's likely to be 80kA? I'm struggling to find any reference material.
  5. B

    am I certified to Sign off fuse board?

    Am I certified to sign off/do certs for a fuse board if I've completed my Level 2 and level 3 city and guilds (2365) electrical installation? (have not done the regs yet or testing & inspection or the NVQ)
  6. H

    Fuse rating confusion

    Organizing my fuse inventory at the plant I came across some Ware 56-50 Amp (FRS style/size). The world of fuses is complicated enough... I cannot find any info on what this seemingly dual rating is. Anyone
  7. L

    Blown Fuse---is it ok to leave blown fuse in and leave electric on.

    We have an older mobile home. One of the fuses keeps blowing. We tried to trace the wire to see if a mouse chewed on the wire perhaps. We think the culprit may be a racoon got the wire...because when we looked under the mobile home to find the wire...there was a racoon....and you can see...
  8. S

    SWA Cable for run between switched fuse isolator and consumer unit

    Hi all, I am looking to replace an existing CU (ground floor) and put it in a new position (first floor). The existing CU is on the inside of a wall to the meter cabinet (which is on the other - external - side of the wall). The existing cabling between these two devices is not SWA/armoured...
  9. N

    Some sockets not working but no fuse blown

    2 sockets in bedroom and 2 in utility room have stopped working. No fuses have blown
    • Nik251
    • Thread
    • blown fuse not working sockets working
    • Replies: 1
    • Forum: DIY Electrical Advice
  10. R

    Fused fuse board no rcd or breakers eicr rating

    Hello I live in a rental in scotland and have recently had an EICR carried out. I have an old fuse wire fuse board on a wooden plate with no rcd or breakers, I had assumed this would be a C1 or C2 but this came back as a C3. Surely this is incorrect if the plastic fuse boards are C3s surely no...
  11. R

    Removal of potential asbestos fuse board - who and estimated cost?

    [EDIT 2056] Sorry, I think I’ve got my wires crossed and OhMe haven’t been very helpful in detailing what I need to do/say to N-Power except for ‘not our problem’. It is indeed the big, green, metal box at the bottom that is the problem. Good evening, Today, I had someone out to install the...
    • Rybeast
    • Thread
    • asbestos board cost fuse fuse board potential removal replacement
    • Replies: 21
    • Forum: UK Electrical Forum
  12. K

    Does 1 Amp make that big of a difference in glass fuses?

    Hello, I have a Chinese 90w laser engraver, and recently the power supply went out. While operating, I heard a pop, and when I disassembled, I found one of the transistors had shorted with a black mark. I have since replaced this power supply, and replaced the fuse that is located in the...
  13. lozarus

    BICC Fuse Carrier Wanted

    An obscure one I know. Currently doing private street light head upgrades. Poles & cutouts originally fitted 1964. Have been re-supplied with PVC SWA at some point (the old SWA is cut off at the bottom, think it must have been cut through at some point). There's only 2 groups of 3 posts, each...
  14. I

    Cellar cooling fuse rating

    A cellar cooling system with the main supply going to the indoor unit. Spec sheet gives the following figures... 12.1amps FLA 65amps LRA 32amp fuse recommended My question: Why a 32amp fuse? Have they based this on HRC fuses perhaps and not advised that? Wouldnt a C-curve 16amp 60898 be...
  15. D

    Backup fuse for SPD?

    Hi everyone , should there be a backup fuse for Q0.1-SPD and what size? Schematic is attached.
  16. P

    Does Ring Transformer Need Fuse?

    Hi, I have recently installed a Ring Pro Doorbell. It has come with a transformer which is going to be connected to the lighting circuit as the CU is too far away. My question is, does it need a Fused Switch on the supply or can it be powered straight from the lighting circuit? Thanks
  17. E

    Dated Consumer unit whats the fuse for

    I saw this dated Wylex CU the other day and not sure what this separate fuseway was for; does anyone know I've never see one like this before !
  18. B

    Advice yes or no? On RCBO fuse installation?

    Got a duel wylex RCB & RCBO board installed some time back. It has space I think for 3 RCBO's. The spark suggested putting the garage feed and the shower feed on rcbo at the time I stuck with the RCB option as a false saving but am now thinking of doing RCBO for garage and shower a suggested...
    • billathome65
    • Thread
    • advice fuse garage installation rcbo
    • Replies: 2
    • Forum: DIY Electrical Advice
  19. M

    Does anyone know what type of fuse this is?

    Does anyone recognise this fuse. It comes from a punch machine , made in Spain, bought in the UK and exported to Canada. Thanks, Mike
  20. V

    Bosch washing machine tripping fuse box

    Hello everyone. I've bought a second hand Bosch series 6 (2 years old, minimal use). The first washing went without any fault during the cycle, but after the cycle fully finished (10 seconds later), the machine tripped the fuse box. I've removed back and top lid to check if any wired connection...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

Tilers | UK Tiling Forum | Tilers Forums | Find a Tiler
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Gas Forum | Unofficial Gas Safe Register Forum
Top Bottom
Back