Connecting speaker wire to audio plugs

[DanUK]

Hi guys. I hope you can help me please?

I need to hook my Tv up to my AV receiver and the only wire that's between the two is a bare speaker wire (red / black). Unfortunately I cannot run any other cables that way due to the way it was plastered back in.

Doing some research it seems it is possible, although not ideal, to add Audio jack (white / red) plugs onto a speaker cable.

I've ordered 2 lots of these from Amazon so I can chop the plugs off and hopefully attach them to the speaker wires: Belkin F3Y116bf1M 1m Portable Y Audio Cable Belkin F3Y116bf1M 1m Portable Y Audio Cable: Amazon.co.uk: Electronics - https://www.amazon.co.uk/dp/B006W95DPU/ref=cm_sw_r_cp_api_66w8yb1G7Z27B

Here's my questions if I may:

1) if I were to chop the ends of the above and strip the wire could I use a terminal block connector to connect them? I.e red speaker wire to the red audio plug wire?

2) would it be better to solder these together?

The terminal connector block I mention is:

3A BLOCK CONNECTOR STRIP for jointing cable 3A BLOCK CONNECTOR STRIP for jointing cable: Amazon.co.uk: DIY & Tools - https://www.amazon.co.uk/dp/B003ZWE7HW/ref=cm_sw_r_cp_api_V8w8ybM30MK8G

Just to also mention there is only one speaker cable so hopefully the red wire can hook up to one, and the black to the other?

Thanks in advance!

 

[dmxtothemax]

Like you said -
it will work but is not ideal,
the main problem is likely to be hum
as the wire is unsheilded
how ever if there is no hum
then you may just get away with it.

 

[Andy-1960]

I'm not sure this will work.

I presume you are hoping to use one core for video and the other for audio.

The problem as I see it is that you only have two cores when you effectively need four.
You need a signal plus a ground for each with the ground usually doubling up with the screen which you don't have.

You may be best looking at a wireless alternative such as One For All SV1760 Wireless HDMI Sender: Amazon.co.uk: Hi-Fi & Speakers - https://www.amazon.co.uk/One-All-SV1760-Wireless-Sender/dp/B01BMG9UE2/ref=pd_day0_23_2?_encoding=UTF8&psc=1&refRID=V86HF0B6W5RAFX197DY2

 

[SparkyChick]

How far have you got to run the cables? And what sort of layout have you got? A photo may help.

 

[Lucien Nunes]

There are two problems with using your speaker cable. One is that it is not shielded (aka screened) so it will tend to pick up interference and hum on the much more sensitive line level connection that you want to make with it. The other is that you only have two conductors when you actually need three, Left, Right and Ground which completes the circut for both channels and would normally be via the shielding.

If the equipment at both ends is grounded to mains earth via nearby socket outlets on the same circuit, then you might be able to send left down one core and right down the other, however it will be even more prone to picking up hum and if the source end gets disconnected from ground while the volume is turned up at the destination, you will get an ear-splitting, speaker-destroying level of buzz. If either end is not grounded (e.g. is double-insulated and has 2-core mains flex) then you would have to add this otherwise you do not have a complete circuit for the audio and you will simply get the horrendous buzz.

The only way you can reliably get clean line-level audio through a speaker cable is to use a balancing transformer at each end to convert the unbalanced phono connections to balanced (symmetrical, neither wire grounded), but in this case you definitely need both cores of the cable for one channel in which case you can only send mono, i.e. you will have to mix L & R at the source and feed the mix into both channels at the destination.

I don't recommend any of the above, I think you will want a wireless solution or a new 2-pair screened cable installed.

 

[Midwest]

What audio 'sockets' at the tv are you intending to use, and what source are you using, Freeview, cable or satellite?

 

[Scratch Music]

I assume its just for audio feed from TV to amp. Your TV will have L and R audio outputs and so will the amp (inputs). You can try using one core for each but, as said by others, the cable should be screened. However, over a short distance, less than 1m, you might be lucky. Try it. Soldered, always.

 

[DanUK]

Thank you very much for the replies. I'm so glad I asked.

Just to clarify it's only for audio (L and R) - the av receiver is a Pioneer VSX330 4K Home Cinema Receiver Pioneer VSX330 4K Home Cinema Receiver: Amazon.co.uk: Electronics - https://www.amazon.co.uk/dp/B014Q2LOMA/ref=cm_sw_r_cp_api_YME8ybAEMV3F6

My idea was to use the 'CD' L and R inputs (second picture shows the back of the receiver).

Unfortunately I literally just have the speaker cable and nothing else. I'd have to look at a wireless option if not.

I do have a spare HDMI running down the wall too, it I don't believe I can get that to the AV receiver? The TV does support ARC but I can't see a HDMI in on the AV receiver.

Thanks again for any further help.

 

[DanUK]

Thank you very much for the replies. I'm so glad I asked.

Just to clarify it's only for audio (L and R) - the av receiver is a Pioneer VSX330 4K Home Cinema Receiver Pioneer VSX330 4K Home Cinema Receiver: Amazon.co.uk: Electronics - https://www.amazon.co.uk/dp/B014Q2LOMA/ref=cm_sw_r_cp_api_YME8ybAEMV3F6

My idea was to use the 'CD' L and R inputs (second picture shows the back of the receiver).

Unfortunately I literally just have the speaker cable and nothing else. I'd have to look at a wireless option if not.

I do have a spare HDMI running down the wall too, it I don't believe I can get that to the AV receiver? The TV does support ARC but I can't see a HDMI in on the AV receiver.

Thanks again for any further help.

Oh, and the speaker cable used was: Manax 50 m Speaker Cable 2x 2.5 mm² White 100% OFC Copper Manax 50 m Speaker Cable 2x 2.5 mm² White 100% OFC: Amazon.co.uk: Electronics - https://www.amazon.co.uk/dp/B00I0UH6TA/ref=cm_sw_r_cp_api_NPE8yb9JF0E2D

 

[Midwest]

You may find this forum more useful;

Audio Video Home Entertainment Resource and Community | AVForums - https://www.avforums.com/

Still wondering what 'audio', you are giving your amp?