Hi all,
I had an assessment yesterday and failed :(. The reason I failed was there were ring circuits that had mcb's and not rcbos. the apartments I showed were ones that the company I work for provided the apartments and are ones in which I installed and tested but were digned 2- 3 years ago...
hi everyone
My mk1 Focus has developed the following electrical problems over a very short period of time (2 weeks). I can't believe that this is due to individual faults and was wondering if anyone could shed any light on the problem and if there is a fault in common easily fixed
Indicators...
Hi all,
Ive recently attended an EAL 4337 & 4338 combined course in Chadderton Oldham, I passed my practical with out to much issue, however I have now failed both Initial and periodic exams TWICE by just a couple of marks (this happened today) now not wanting to apportion blame but the other...
Tested a Crabtree Polestar board today full of Sector rcbos, tested many of these boards and never seen this. The only Crabtree devices were two mcbs but the Sector devices are identical to Crabtree devices. Out of the nineteen four failed which is something you don't get with Crabtree rcbos...
Good morning, everybody. I have just registered on these forums in order that I might seek some advice re a car electrics issue. I am not an electrician so I have not bothered introducing myself on the welcome page. Hopefully this is acceptable.
I am trying to help an elderly friend get his...
Hi All
I would be very grateful if anyone has experienced and failed Astro Terra 28 (or others) LEDs. I have recently wired parallel and series over the years but have stumbled recently on how 6x 1w leds failed using a 5.95-10w 350mA constant current led driver. I have tested the circuit which...
Hi, lookin for a bit info for a mate, he has been in the fire alarm industry for about 15 years and done the college of an electrical apprenticeship but never passed the fica, would he be able to do his fica after all this time ?
Thanks in advance
Hi,
I would have thought it unusual for an RCD to fail? However, I have come across a Wylex WRS80/2 which gives >400ms reading for the 1X RCD test using a Megger 1552MFT. A no trip fail.
Could there be some other reason for this result?
Any help appreciated.
Regards,
Trenelly
Hi all, just trying to find out whether anyone has come across a similar issue with Orona lifts? We have been notified that
ropes have failed as a result of unequal spring tension in the ropes. Could this be manutacturer's fault at all? thanks for any advice.
Hi All,
It looks like I have a failed SE optimiser (showing zero voltage on monitoring portal). The system was installed in November 2011.
My installation company appears to have been dissolved. What are my options for getting it replaced?
We are in SN14, near Bath.
Thanks,
Andy
Hiya guys
i carried out an EICR yesterday all the tests were fine, tns system but when I got to the rcd test it failed on the X1 and x5 test saying >300 and >40, so I put a new rcd module in and it failed again, it's an mk sentry board, any ideas before I just change the whole board ??? Also...
This is long, so apologies but I have never come across this before.
I got asked by my local garage where I get my van MoT'd if I could do an EICR for him as his insurance company have requested one.
So I pitch up today and the owner produced a load of old PIR's and EICR's that have been...
Hi all
had my am2 recently, failed on the earth loop test.
Passed es everything else no bother
apparently after doing my Ze I never put the cover back on the board before doing my Zs's didn't think about it because I was in a little booth, I real life I would have to leave the DB to find the...
Hi, before taking my am2 I read some very helpful threads from this site. So anyone reading this also preparing I hope this helps I got through my install and testing fine. However I failed the fault finding C2. passed C1. Whatever that means. I did all my tests at the board and struggled on...
Hi just found out a have failed my am2 on the installation section
Firstly I wondered if I can get any information on how I failed apart from them saying what circuits I failed on ( lighting/ bonding and swa to 16amp socket )
I thought I did all these correctly and can't see what I can fail on...
Hi I'm going back to Hota in Hull to resist my I.S installation, I failed on a major and very little else that's all I know, was wondering if anyone could share any pointers or tips on what to look out for on the I.S installation , hoping to get my compex qualification after this resit any help...
Liamg86
Thread
advice
anyone
compex
failed
installation
instrument
little
major
please
Compex Ex01 - 04 refresher notes
Hello guys
I've got my compex refresher this week and was wonder if anyone has any notes or advice for me ?
ive been reading the toolbox book for a few days and I feel quite confident on that but i know things can change on the day in test conditions
thomson_adam
Thread
compex
course
failed
led
notes
questions
refresher
unit
Ive used Bosch power tools for years without problems,
However both batteries on my Bosch 36v SDS have failed within weeks of each other and the drill is just out of warranty. One battery wont hold any charge, one will only hold enough for two rawlplugs
There seems to be several option, the...
SRP manufactured Sunnyroo inverters a few years back, they were sold as "made in Australia" they were infact made in China by a company that went out of business a couple of years back.
I ended up with a failed unit which I had to replace out of my own pocket because the warranty is now...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.