Hi.
I am planing on building a (not sure what to call it) U shaped storage solution which goes either side and above the headboard of a bed. I want to install a couple of reading lights either side.
A mixture of me not being bothered and running out of money means I cant run cable on the...
Got a 2005 mk5 golf 1.9tdi
Was running perfect then I wired in a subwoofer it was fine for couple days got in the car today now my power steering is stiff and light I's on, indecators and high beams wont work neither will my radio checked all fuses with a multi metre and they are fine any...
Hi . Im running some conduit , a long horizontal with metal clad boxes , with vertical runs to a term box for light fittings and a couple of smoke alarms . Was going to use 4 way boxes dropping down to the sockets and up to the light s. Is it acceptable to run them through the metal clad boxes...
Hi
I have to run a feed to a CU in the middle of a ground floor flat . Its already got 2 layers of blue board and 100mm rockwool above it . It would be clipped in the ceiling over 50mm above the ceiling height . rockwool in the jist space and 2 layers of pink board below . So method 101 ...
Our solar system was installed 8 years ago. We had no problems until EON replaced our smart meter, and our electricity and gas meters with it. Since then, our PV generation meter has gone mad. Running all day and all night, to the extent that British Gas refused to pay our FIT, because of the...
Hi, I live in Australia. I have a Crypto mining rig that will soon have 3/1200w power supplies attached to a 10a power board drawing more than 2400w and that will be attached to a 15a wall socket (That usually runs the air con)...Can I run more than 2400w through that system? Is that safe...
I came up with an idea that could possibly produce more useful energy than is required to keep the system running & no it is not a perpetual motion machine.
The output is electric and that is why I am introducing this idea here.
SeaPower description
Attached is a diagram that details a new...
Hi all,
Hoping you can help.
My house has a ring in the kitchen that is no longer wired direct to the consumer unit as it had a fault and kept blowing. It was believed that it might be an 'open ring' and a socket had been removed from the ring at some time in the past. (I think that was what...
Hi,
This is my first post and was wondering if anyone could help :)
I moved into my 1 bed flat about 7 months ago - the flat has single glazed windows and all electric. Our electric heating is Thermaskirt - so the heating is in the skirting boards and our meters are digital and have Economy 7...
Rewiring an old home where basement lines will feed the first floor (multiple 15/20 Amp w/ 12/2 & 12/3 romex & a single 50 Amp 6/3 romex supplying range. If I run cables over a wall to feed the first floor, how often would do they need to be fastened/stapled, are there exceptions (such as when...
Hi everyone, hope you’re all doing well.
Got a job starting next week for a rewire of a studio flat, currently they have 10 mm T&E as metre tails , So definitely got to be an upgrade.
The existing meter box is situated outside ( under cover ) the bathroom wall , On the right hand side of the...
Hi all,
I've got a question and I'm not sure if anyone can help?
I have recently built a gazebo and as part of the built I required sockets and lighting.
As with these sorts of things the gazebo was no where near the main board. So firstly I already had an outside socket IP66 (not a spur)...
Refreshing my knowledge on circuits for an electric project & would appreciate if you can let me know if my understanding as I will explain/show below is correct.
Figure 1 shows a wire containing a live (red) & neutral (red) (similar to Romex NMB w/out ground shown) and Each bulb A-D are...
I am needing to know if this wiring diagram is showing a few things:
1: Does this show a 3 phase to single phase conversion?
2: Does this show that the motor can turn in 2 directions with the same internal wiring if you toggle the SPDT switch?
Hi all.
I'm thinking about adding a garden office and will obviously need power. Can power be taken from a normal plug socket somewhere at the rear of the house, or does it need its own circuit from the main consumer unit? If it needs it's own circuit it's a non starter project as I don;t want...
I have quite a bit a cat5e to run through joists under floorboards for ethernet points around the house. Can this run in the same joists as the LV cables or do you make separate holes in the joists for the ELV cables?
Cheers guys.
Morning..
I'm having an ethernet point next to a tv aerial socket. Is it ok to run the cat5e and coax in the same chase. As I understand it I just have to keep LV 50mm away from ELV, so as these are both ELV its ok?
Cheers all.
As title, select the correct settings L-L L-E on left and As on right, am unable to change mode (2Lo 2Hi etc.
Screen comes up with <50v but does nothing else.
Any ideas? Runs continuity and IR fine, not tried RCD
I have been to look at a rewire. The builders have pretty much taken the house apart and I have found the neighbours supply cables hanging above my customers ceiling.
The customers line supply cable comes into the top of the cutout and then another line supply comes out of the top and off to...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.